This work investigates a ferrite matrix with multiple non-metallic inclusions to evaluate their influence on the global and local deformation and damage behavior of modified 16MnCrS5 steel. For this purpose, appropriate specimens are prepared and polished. The EBSD technique is used to record local phase and orientation data, then analyze and identify the size and type of inclusions present in the material. The EBSD data are then used to run full phase crystal plasticity simulations using DAMASK-calibrated material model parameters. The qualitative and quantitative analysis of these full phase simulations provides a detailed insight into how the distribution of non-metallic inclusions within the ferrite matrix affects the local stress, strain, and damage behavior. In situ tensile tests are carried out on specially prepared miniature dog-bone-shaped notched specimens in ZEISS Gemini 450 scanning electron microscope with a Kammrath and Weiss tensile test stage. By adopting an optimized scheme, tensile tests are carried out, and local images around one large and several small MnS inclusions are taken at incremental strain values. These images are then processed using VEDDAC, a digital image correlation-based microstrain measurement tool. The damage initiation around several inclusions is recorded during the in situ tensile tests, and damage initiation, propagation, and strain localization are analyzed. The experimental results validate the simulation outcomes, providing deeper insight into the experimentally observed trends.

Herein, micromechanical material deformation behavior of medium carbon steel—with varying cementite particle size and distribution—under monotonic tensile load is modeled. The statistical phase morphology data are collected from the microscopy images of 83% spheroidized C45EC steel. Virtual microstructures for nine different cases are constructed using Dream.3D by varying the concentrations of small, large, and bimodal cementite particles on the ferrite grain boundaries. A crystal plasticity‐based numerical simulation model, i.e., DAMASK, is used to simulate the local material deformation behavior. The material model parameters for elastic–plastic ferrite and elastic cementite phases are adopted from the literature and calibrated by modifying the fitting parameters to match the experimentally observed material flow curve. It is observed that the cementite particle size and distribution in the primary phase affect the local mechanical behavior of the material. An analysis of deformation at 20% of global strain has helped in the qualitative understanding of factors affecting the stress and strain concentration points. The evolution of stresses and strains in the least and the most stressed representative volume elements (RVEs) has provided interesting information regarding the path followed by the dislocation movement during deformation. The study has provided insight into the factors affecting the material's global and local deformation behavior.

In this research, the effect of 2D and 3D Representative Volume Element (RVE) on the ductile damage behavior in single-phase (only ferrite) and dual-phase (ferrite and martensite) steels is analyzed. Physical and fitting parameters of the constitutive model for bcc-ferrite and bcc-martensite phases are adapted from the already published work. Crystal plasticity (CP) based numerical simulations without damage consideration are run and, later, ductile damage criteria for the ferrite phase is defined for all cases. The results of the non-damage (-nD-) and damage (-D-) simulations are compared to analyze the global and local differences of evolving stresses and strains. It is observed that for the same model parameters defined in all cases, damage initiation occurs at the overall higher global strain in the case of 3D compared to 2D. Based on statistical data analysis, a systematic comparison of local results is carried out to conclude that the 3D RVEs provide better quantitative and qualitative results and should be considered for such full phase simulations. Whereas 2D RVEs are simple to analyze and provide appropriate qualitative information about the damage initiation sites.

This study analyses the effect of martensite grain size and its volume fraction in dual-phase (DP) steel on (1) the formability limit, (2) average global behavior under different loading conditions, and (3) damage initiation. The virtual RVEs (Representative Volume Elements) were constructed using DREAM.3D software with a variation of microstructural attributes. The numerical simulations were carried out using DAMASK, which evaluates the polycrystalline material point behavior and solves versatile constitutive equations using a spectral solver. The simulations were post-processed to obtain global and local stress, strain, and damage evolution in constructed RVEs. The global results were processed to obtain FLDs according to Keeler-Brazier (K-B) and Marciniak and Kuczynski (M-K) criteria. In this work, the capability of microstructure-based numerical simulations to analyze the FLDs has been established successfully. From Forming Limit Diagrams (FLDs), it was observed that formability changes by changing the strain hardening coefficients (n-values), the martensite fraction, and martensite grain sizes of DP steels. The improved formability was observed with lower martensite fraction, i.e., 17%, decreased martensite grain size, i.e., 2.6 µm, and higher strain hardening coefficient. The M-K approach shows the better capability to predict the formability by various loading conditions and clarifies the necking marginal zone of FLD. The damage propagation is also strongly affected by the loading conditions. The current study would be a good guide for designers during the manufacturing and selecting of appropriate DP steels based on the service loading conditions.

This research uses EBSD data of two thermo-mechanically processed medium carbon (C45EC) steel samples to simulate micromechanical deformation and damage behavior. Two samples with 83% and 97% spheroidization degrees are subjected to virtual monotonic quasi-static tensile loading. The ferrite phase is assigned already reported elastic and plastic parameters, while the cementite particles are assigned elastic properties. A phenomenological constitutive material model with critical plastic strain-based ductile damage criterion is implemented in the DAMASK framework for the ferrite matrix. At the global level, the calibrated material model response matches well with experimental results, with up to ~97% accuracy. The simulation results provide essential insight into damage initiation and propagation based on the stress and strain localization due to cementite particle size, distribution, and ferrite grain orientations. In general, it is observed that the ferrite–cementite interface is prone to damage initiation at earlier stages triggered by the cementite particle clustering. Furthermore, it is observed that the crystallographic orientation strongly affects the stress and stress localization and consequently nucleating initial damage.