Globally, corrosion is the costliest cause of the deterioration of metallic and concrete structures, leading to significant financial losses and unexpected loss of life. Therefore, corrosion monitoring is vital to the assessment of structures’ residual performance and for the identification of pathologies in early stages for the predictive maintenance of facilities. However, the high price tag on available corrosion monitoring systems leads to their exclusive use for structural health monitoring applications, especially for atmospheric corrosion detection in civil structures. In this paper a systematic literature review is provided on the state-of-the-art electrochemical methods and physical methods used so far for corrosion monitoring compatible with low-cost sensors and data acquisition devices for metallic and concrete structures. In addition, special attention is paid to the use of these devices for corrosion monitoring and detection for in situ applications in different industries. This analysis demonstrates the possible applications of low-cost sensors in the corrosion monitoring sector. In addition, this study provides scholars with preferred techniques and the most common microcontrollers, such as Arduino, to overcome the corrosion monitoring difficulties in the construction industry.
Structural damage detection using inclinometers is getting wide attention from researchers. However, the high price of inclinometers limits this system to unique structures with a relatively high structural health monitoring (SHM) budget. This paper presents a novel low-cost inclinometer, the low-cost adaptable reliable angle-meter (LARA), which combines five gyroscopes and five accelerometers to measure inclination. LARA incorporates Internet of Things (IoT)-based microcontroller technology enabling wireless data streaming and free commercial software for data acquisition. This paper investigates the accuracy, resolution, Allan variance and standard deviation of LARA produced with a different number of combined circuits, including an accelerometer and a gyroscope. To validate the accuracy and resolution of the developed device, its results are compared with those obtained by numerical slope calculations and a commercial inclinometer (HI-INC) in laboratory conditions. The results of a load test experiment on a simple beam model show the high accuracy of LARA (0.003 degrees). The affordability and high accuracy of LARA make it applicable for structural damage detection on bridges using inclinometers.
Structural Health Monitoring (SHM) programs play a critical role in civil engineering, particularly for evaluating safety conditions and forecasting the strength of large structures such as bridges. Therefore, employing low-cost sensors with implementing different techniques to improve their accuracy compared to high-cost accurate sensors has attracted much attention for structural assessments. In fact, with adequate code and the proper mode to utilize their features and potentials, there is a probability of acquiring valuable data from these low-cost sensors, which can provide helpful insight for the SHM systems. Hence, this study proposes the use of a low-cost circuit for angular measurements based on the fusion of an accelerometer, a gyroscope, and a magnetometer sensor with an Arduino board. In this study, firstly, an introduction through Arduino due and the used sensor is presented. Then angular data acquisition problems, as well as their respective solutions, are presented.
Recently Structural Health Monitoring (SHM) is attracting so much attention due to the global structural stock’s growing era. SHM is a system including sensors and management algorithms that provide non-destructive in-situ information about a structure’s performance condition or health. Therefore, lately, the demand for adopting low-cost sensors for static or dynamic Structural System Identification (SSI) has increased. This paper introduces and evaluates different low-cost sensors mainly used in the bridges SHM applications. Firstly, the Arduino Uno, which is the programmable logic controller, and diverse sensors such as Ultrasonic, Laser, Gyroscope, Accelerometer, Temperature-humidity were introduced. Secondly, different tests were applied in controlled ambient situations to identify difficulties during sensor installation and data acquisition. This study presents solutions for encountered problems in order to use these low-cost electronic devices efficiently for SHM purposes.
Since the Structural Health Monitoring applications are getting significant attention from scientists and engineers, a new system has been introduced. This device is capable of acquiring vibrations with a sampling frequency of up to 85 Hz. In this paper, the effect of having several synchronized accelerometers on a rigid plate for improving the resolution and accuracy of a new vibration acquisition system is investigated.An experimental test has been carried out to investigate the reliability of the claimed theory. Accelerometers made from combining one, two, three, four and five low-cost low-resolution accelerometers are made and tested on a shaking table. The overall results show that the number of combined accelerometers has an indirect ratio with the obtained noise density of the final product.
Nowadays, accelerometers are used widely by civil engineers for Structural Health Monitoring (SHM) purposes. The expensive cost of acquisition equipment and accelerometers have made the SHM applications unavailable for structures with relatively low budgets for their assessment.A new accelerometer has been proposed in this paper. This accelerometer is a uniaxial accelerometer with a sampling frequency of up to 85Hz. Although the proposed accelerometer is 17 times cheaper than a traditional accelerometer (PCB 393A03), it provides a better resolution and accuracy at the same time. An experimental test has been carried out for comparing the proposed accelerometer with PCB 393A03 sensor.