Seven aromatic polyamides and copolyamides were synthesized from two different aromatic diamines: 4,4′-(Hexafluoroisopropylidene)bis(p-phenyleneoxy)dianiline (HFDA) and 2,4-Aminobenzenesulfonic acid (DABS). The synthesis was carried out by polycondensation using isophthaloyl dichloride (1SO). The effect of an increasing molar concentration of the sulfonated groups, from DABS, in the copolymer properties was evaluated. Inherent viscosity tests were carried out to estimate molecular weights. Mechanical tests were carried out under tension, maximum strength ( max), Young’s modulus (E), and elongation at break (εmax) to determine their mechanical properties. Tests for water sorption and ion exchange capacity (IEC) were carried out. Proton conductivity was measured using electrochemical impedance spectroscopy (EIS). The results indicate that as the degree of sulfonation increase, the greater the proton conductivity. The results obtained showed conductivity values lower than the commercial membrane Nafion 115 of 0.0065 S cm−1. The membrane from copolyamide HFDA/DABS/1S0-70/30 with 30 mol DABS obtained the best IEC, with a value of 0.747 mmol g−1 that resulted in a conductivity of 2.7018 × 10−4 S cm−1, lower than the data reported for the commercial membrane Nafion 115. According to the results obtained, we can suggest that further developments increasing IEC will render membranes based on aromatic polyamides that are suitable for their use in PEM fuel cells.
The recovery and reuse of high-impact polystyrene (HIPS) into high-value products is crucial for reducing environmental thermoplastics waste and promoting sustainable materials for various applications. In this study, asymmetric membranes obtained from sulfonated HIPS waste were used for salt and dye removals. The incorporation of sulfonic acid (-SO3H) groups into HIPS waste by direct chemical sulfonation with chlorosulfonic acid (CSA), at two different concentrations, was investigated to impart antifouling properties in membranes for water treatment. Asymmetric membranes from recycled HIPS, R-HIPS, R-HIPS-3, and R-HIPS-5 with 3 and 5% sulfonation degrees, respectively. Sulfonated HIPS shows a decrease in water contact angle (WCA) from 83.8° for recycled R-HIPS to 66.1° for R-HIPS-5, respectively. A WCA decrease leads to an increase in antifouling properties for R-HIPS-5, compared to non-sulfonated R-HIPS, which leads to a higher flux recovery ratio (FRR) and enhanced separation properties for sulfonated membranes. The HIPS-5 membrane exhibited the highest rejection rates for Reactive Black 5 dye (94%) and divalent salts (72% for MgSO4 and 67% for Na2SO4). The performance of the recycled HIPS asymmetric membranes is well correlated with porosity, water uptake, and the higher negative charge from the sulfonic acid groups present, which enhance the electrostatic repulsions of salts and dyes.
Kinetic rigidity of several polymers such as 2,6-bis(3-aminophenoxy)benzonitrile/4,4′oxydiphthalic anhydride (β-CN)APB/ODPA, poly[(2,2-dimethyl-1,3-dioxolan-4-yl)methyl acrylate)] (PACGA), and diglycidyl ether of bisphenol A (DEGEBA) was studied. Rigidity parameter D , Vogel’s temperature T0 , and the activation energy Uα ( Tg ) for the glass transition were evaluated through Vogel’s model along with relaxation data using “nonlinear” regression of Arrhenius function. The existence of certain functional groups within the structure, such as the aromatic rings, gives high level of kinetic rigidity to the structure as is the case of (β-CN)APB/ODPA and DEGEBA , while the aliphatic groups confer flexibility, as in PACGA.