Marko Djokic

Dr. Marko Djokic

Laboratory for Chemical Technology, Department of Materials, Textiles and Chemical Engineering, Ghent University
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2012 in Journal of Chromatography A
Verified
Journal Article
Closed access
MDMarko Djokic
Marko Djokic
TDThomas Dijkmans
Thomas Dijkmans
GYGüray Yildiz
Güray Yildiz
WPWolter Prins
Wolter Prins
Kevin Van GeemKevin Van Geem
Kevin Van Geem

1 September 2014 in Journal of Chromatography A
Verified
Journal Article
Closed access
HTHilal E. Toraman
Hilal E. Toraman
TDThomas Dijkmans
Thomas Dijkmans
MDMarko Djokic
Marko Djokic
Kevin Van GeemKevin Van Geem
Kevin Van Geem
GMGuy B. Marin
Guy B. Marin

24 October 2018 in Industrial & Engineering Chemistry Research
Verified
Journal Article
Open access
SSSteffen H. Symoens
Steffen H. Symoens
NONatalia Olahova
Natalia Olahova
AGAndrés Eduardo Muñoz Gandarillas
Andrés Eduardo Muñoz Gandarillas
HKHadiseh Karimi
Hadiseh Karimi
MDMarko Djokic
Marko Djokic
Kevin Van GeemKevin Van Geem
Kevin Van Geem
Although steam cracking is a mature technology, mitigation of coke formation remains one of the main challenges in the petrochemical industry. To increase the olefin output of existing plants, coil materials that can withstand higher temperatures are desired. This work reviews material technologies that were developed and tested in the past three decades to minimize the rate of coke deposition and extend the furnace run length. The material not only determines the mechanical properties of the coil but also affects the coking rate substantially. In some cases more than a factor 10 differences in coking rates have been observed. SiC materials could be operated at significantly higher temperatures and this leads to higher olefin selectivity if one includes acetylene hydrogenation, however the mechanical joints make it currently impossible to take advantage of their superior temperature resistance. On industrial scale operational improvements have been reported with advanced reactor surface technologies such as high performance alloys and coatings during the last decade. Catalytic coatings go a step further than barrier coatings by actively removing coke that is deposited on the coils. Another trend is to add aluminum to the coil material, which forms a protective aluminum oxide layer on the reactor wall during operation, and results in reduced carburization. To optimize the coking mitigation capabilities of the coils, the state-of-the-art materials and/or coatings should be combined with 3D reactor technologies, which is not always possible for all materials because of the advanced machining that is needed.

1 January 2015 in Fuel
Verified
Journal Article
Closed access
TDThomas Dijkmans
Thomas Dijkmans
MDMarko Djokic
Marko Djokic
Kevin Van GeemKevin Van Geem
Kevin Van Geem
GMGuy B. Marin
Guy B. Marin

1 September 2013 in Journal of Analytical and Applied Pyrolysis
Verified
Journal Article
Closed access
GYGüray Yildiz
Güray Yildiz
MPMarty Pronk
Marty Pronk
MDMarko Djokic
Marko Djokic
Kevin Van GeemKevin Van Geem
Kevin Van Geem
FRFrederik Ronsse
Frederik Ronsse
WPWolter Prins
Wolter Prins

1 November 2014 in Combustion and Flame
Verified
Journal Article
Closed access
MDMarko Djokic
Marko Djokic
Kevin Van GeemKevin Van Geem
Kevin Van Geem
CCCarlo Cavallotti
Carlo Cavallotti
AFAlessio Frassoldati
Alessio Frassoldati
EREliseo M. Ranzi
Eliseo M. Ranzi
GMGuy B. Marin
Guy B. Marin