Marshed Kassim Mohamed

Dr. Marshed Kassim Mohamed

Department of Electronic Systems, Norwegian University of Science and Technology, Trondheim, Sør-Trøndelag, Norway
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 March 2020 in IEEE Access
Verified
Journal Article
Open access
Ahmed Al-SamanAhmed Al-Saman
Ahmed Al-Saman
MCMichael Cheffena
Michael Cheffena
Marshed Kassim MohamedMarshed Kassim Mohamed
Marshed Kassim Mohamed
MAMarwan Hadri Azmi
Marwan Hadri Azmi
YAYun Ai
Yun Ai
The high frequencies of millimeter wave (mm-wave) bands have been recognized for the fifth generation (5G) and beyond wireless communication networks. However, the radio propagation channel at high frequencies can be largely influenced by rain attenuation, especially in tropical regions with high rainfall intensity. In this paper, we present the results of rainfall intensity and rain attenuation in tropical regions based on one-year measurement campaign. The measurements were conducted from September 2018 until September 2019 at 21.8 GHz (K-band) and 73.5 GHz (E-band) in Malaysia. The rainfall intensity was collected using three rain gauges installed along a 1.8 km link. The rain attenuation is computed from the difference between the measured minimum received signal level (RSL) during clear sky and rain conditions. The measured rain rate and rain attenuation distributions are then analysed and benchmarked with several previous measurements and well-known prediction models such as the ITU-R P. 530-17. The rainfall rate results showed that the best agreement between the measured rainfall rate in Malaysia and the ITU-R PN.837-1 prediction value for Zone P is up to 0.01% of time (99.99% of time agrees well and only disagrees for 0.01% of time). For the E-band, the maximum measured rain attenuation exceeding 0.03% of the year is around 40.1 and 20 dB for 1.8 and 0.3 km links, respectively, at the maximum rain rate of 108 mm/h. For the K-band, the maximum rain attenuation exceeding 0.01% of the year is around 31 dB for the 1.8 km link. Finally, the rain rates exceeding 108 and 180 mm/h at 73.5 and 21.8 GHz, respectively, along the 1.8 km path caused an outage on our measurement setup. The rain rate of 193 mm/h and above caused an outage for the 0.3 km E-band link. The experimental data as well as the presented data analysis can be utilized for efficient planning and deployments of mm-wave wireless communication systems in tropical regions.

11 September 2017 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
MCMichael Cheffena
Michael Cheffena
Marshed Kassim MohamedMarshed Kassim Mohamed
Marshed Kassim Mohamed
In this letter, practical sensor nodes are utilized to study the path loss effects of wireless sensor networks (WSNs) at 2.425 GHz in a ground covered by snow at different heights from the ground. The measurement results are compared with the ground reflection (two-ray) path loss model and the ray-tracing model showing significant difference. New empirical path loss models for different heights from the ground based on the log-distance path loss model are presented. The developed models are compared with the existing path loss models to demonstrate their accuracy between sensor nodes deployed in snowy environments. The experimental data as well as the developed path loss models can be utilized for efficient planning and deployments of WSNs in snowy environments. They can support applications including rescue and monitoring of snow avalanche, environmental surveillance, or monitoring winter sporting activities.

12 March 2021 in Sensors
Verified
Journal Article
Open access
PDF file
Ahmed Al-SamanAhmed Al-Saman
Ahmed Al-Saman
Marshed Kassim MohamedMarshed Kassim Mohamed
Marshed Kassim Mohamed
MCMichael Cheffena
Michael Cheffena
AMArild Moldsvor
Arild Moldsvor
Wireless data traffic has increased significantly due to the rapid growth of smart terminals and evolving real-time technologies. With the dramatic growth of data traffic, the existing cellular networks including Fifth-Generation (5G) networks cannot fully meet the increasingly rising data rate requirements. The Sixth-Generation (6G) mobile network is expected to achieve the high data rate requirements of new transmission technologies and spectrum. This paper presents the radio channel measurements to study the channel characteristics of 6G networks in the 107–109 GHz band in three different industrial environments. The path loss, K-factor, and time dispersion parameters are investigated. Two popular path loss models for indoor environments, the close-in free space reference distance (CI) and floating intercept (FI), are used to examine the path loss. The mean excess delay (MED) and root mean squared delay spread (RMSDS) are used to investigate the time dispersion of the channel. The path loss results show that the CI and FI models fit the measured data well in all industrial settings with a path loss exponent (PLE) of 1.6–2. The results of the K-factor show that the high value in industrial environments at the sub-6 GHz band still holds well in our measured environments at a high frequency band above 100 GHz. For the time dispersion parameters, it is found that most of the received signal energy falls in the early delay bins. This work represents a first step to establish the feasibility of using 6G networks operating above 100 GHz for industrial applications.

7 July 2021 in IEEE Electromagnetic Compatibility Magazine
Verified
Journal Article
Closed access
Marshed Kassim MohamedMarshed Kassim Mohamed
Marshed Kassim Mohamed
BMBaraka J. Maiseli
Baraka J. Maiseli
YAYun Ai
Yun Ai
KMKhadija Mkocha
Khadija Mkocha
AAAhmed Al-Saman
Ahmed Al-Saman
Wireless body area networks (WBANs) consist of interconnected devices that monitor the human body functions and the surrounding environment. Of these sensors, implants encounter multiple challenges due to their invasive nature. In addition, the transmission channel of the implants involves living tissues that pose practical challenges in channel modeling. Despite several promising applications of implants in the healthcare industry, there have been insufficient comprehensive reviews that extensively describe trends and challenges of this technology. This work reviews in-body WBANs and presents critical challenges that hinder advancement and application of the technology. We also discuss possible solutions that may be useful to realize in-body WBANs practically.

2 January 2017 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
Marshed Kassim MohamedMarshed Kassim Mohamed
Marshed Kassim Mohamed
MCMichael Cheffena
Michael Cheffena
AMArild Moldsvor
Arild Moldsvor
FFFernando P. Fontan
Fernando P. Fontan
In this letter, a physical-statistical-based channel model for off-body wireless communications is presented. The model utilizes a dynamic human walking model, which provides detailed description of the movement of the different body parts. The received signal is composed of a direct component, which might be subject to shadowing by the body parts, and a multipath component due to reflections from the environmental scatterers. The uniform theory of diffraction (UTD) is utilized to accurately calculate the time-varying shadowing and scattering effects of the direct signal due to the moving of body parts. A Rayleigh distribution is used to represent the multipath fading effects by the scatterers around the human body. The model is validated in terms of first- and second-order statistics using 2.36 GHz measurement data, showing good agreement.

27 June 2018 in IEEE Sensors Journal
Verified
Journal Article
Open access
Marshed Kassim MohamedMarshed Kassim Mohamed
Marshed Kassim Mohamed
MCMichael Cheffena
Michael Cheffena
Expansion of wireless body area networks applications, such as health-care, m-banking, and others has lead to vulnerability of privacy and personal data. An effective and unobtrusive natural method of authentication is therefore a necessity in such applications. Accelerometer-based gait recognition has become an attractive solution, however, continuous sampling of accelerometer data reduces the battery life of wearables. This paper investigates the usage of received signal strength indicator (RSSI) as a source of gait recognition. Unlike the accelerometer-based method, the RSSI approach does not require additional sensors (hardware) or sampling of them, but uses the RSSI values already available in all radio devices. Three radio channel features namely, the time series, auto-correlation function, and level crossing rate were extracted from unique signature of the RSSI in relation to the corresponding subject. The extracted features were then used together with four different classification learners, namely decision tree, support vector machine, k-nearest neighbors, and artificial neural network, to evaluate the method. The best performance was achieved utilizing artificial neural network with 95% accuracy when the features were extracted from one on-body radio channel (right wrist to waist), and 98% when the features were extracted from two on-body radio channels (right wrist to waist, and left wrist to waist). The developed RSSI-based gait authentication approach can complement high-level authentication methods for increased privacy and security, without additional hardware, or high energy consumption existing in accelerometer-based solutions.