The feasibility of producing sustainable cement-free composites and its environmental impact were investigated in this research. Experimental parametric evaluation was carried out in this regard to explore the optimum mix design of the composites. The effect of synthesis parameters and curing conditions on the behavior of the produced geopolymer composites was investigated. The studied parameters included the molarity of the sodium hydroxide solution (12 M, 14 M, and 16 M), the sodium silicate to sodium hydroxide ratio (1, 1.5, 2, and 2.5), the fluid to binder ratio (0.6, 0.65, and 0.7), and the age. The curing conditions included ambient curing and heat treatment at 40 °C, 80 °C, and 120 °C for 24 h, 48 h, and 72 h. In addition, life cycle assessment was performed to compare the environmental impact of geopolymer and cementitious composites. The results reflected the possibility of producing geopolymer composites with significant positive environmental impacts over traditional cementitious composites. The synthesis parameters played a major role in the behavior of the produced geopolymers. Heat curing was necessary for the geopolymer mortar to achieve high early strength. However, strength development with age was more obvious for ambient-cured specimens than heat-cured specimens. The optimum fluid to binder ratio used in this research was 0.6. For this ratio, the compressive strength increased as the molarity of the sodium hydroxide solution increased for all sodium silicate to sodium hydroxide ratios. Finally, SEM images showed that the higher the molarity and as the amount of reacted FA particles increased, the better the microstructure of the geopolymer mortar was and the fewer pores the matrix had.
The construction sector is well known for its critical environmental impact resulting from the consumed amounts of raw materials and the tremendous emissions of greenhouse gases. Therefore, scientists need to promote and study the environmental implications of using alternative solutions such as fiber-reinforced polymers (FRP) throughout their service life. FRPs have gained increasing popularity in the last few years due to their durability, high corrosion resistance, light weight and high strength. Life cycle assessment is considered one of the most important methods to investigate the environmental impacts of the FRP. The aim of this paper is to present an overview of fiber-reinforced polymer composites in concrete structures with an investigation focusing on their environmental and mechanical properties in civil engineering structures. The main focus is set on the properties of fiber-reinforced polymers, their use as a strengthening technique in concrete structural members and their environmental impact using the life cycle assessment method. The reported results from the literature reveal that utilizing FRP composites in structural members instead of traditional materials improves their strength and stiffness and reduces environmental impacts.
1 August 2021 in Construction and Building Materials
This paper experimentally studied the effect of polypropylene (PP) microfibers on thermal and post-heating mechanical behaviors of cementitious composites. Cement mortars with small dosage of polypropylene fibers were prepared, heated at various temperatures (150 °C, 200 °C, 450 °C, and 600 °C), and then tested. The investigated parameters include residual compressive and flexural strengths, elastic modulus, fracture energy, stress intensity factors, failure modes, microstructure (scanning electron microscopy (SEM) imaging), thermal conductivity, heat flow (differential scanning calorimetry (DSC) test), mass loss (thermogravimetric analysis (TGA) test), and chemical composition (XRD analysis). The results showed the efficiency of PP fibers to enhance the post-heating behavior and the residual mechanical properties of cement mortar after heating. The presence of PP fibers did not affect the heat flow and the mass loss of cement mortar at room temperature. However, heating cement mortar at temperature beyond the melting point of the fibers negatively affected its thermal behavior. The presence of PP fibers played a major role in bridging the cracks and mitigating their propagation. Once the melting point of the polypropylene fibers is exceeded, the fibers melted and created extra voids in the microstructure of concrete.
4 April 2022 in Construction and Building Materials
This paper experimentally investigates the influence of carbon nanotubes (CNTs) on phase composition, microstructure deterioration, thermal behavior, and residual mechanical strengths of cementitious composites exposed to elevated temperatures. Cement mortars with small dosages of CNTs, 0.05% and 0.2% by weight of cement, were prepared and then heated at 25 °C, 150 °C, 200 °C, 450 °C, and 600 °C for two hours before being tested. The results show positive impact of the CNTs on the hydration process of cement mortar at room temperature and at higher temperatures up to 200 °C. Decomposition of the hydration products is obvious at 450 °C, whereas sever deterioration in the microstructure occurs at 600 °C. The nano reinforcement and bridging effect of the CNTs are obvious up to 450 °C. Thermal behavior characterization shows that CNTs incorporation enhances the thermal conductivity of the unheated and heat-treated mortar specimens. The decomposition of the hydration products needs more heat in the presence of CNTs. Finally, presence of CNTs significantly enhances the residual compressive and flexural strengths of heated mortar specimens for all studied temperatures.