Using a lapped seam, PVC-coated hybrid textiles with uniform thickness were bonded by continuous ultrasonic welding and conventional joining method with the help of hot air tape welding technique for weather protection purposes. Three fundamental sewing parameters at two distinct levels and three primary welding parameters at three levels based on 6 and 12 mm welding widths were used. To consider the effect of welding and sewing parameters on seam strength, full factorial designs of experiments were designed, fabricated, and tested. The thermal behavior and possibility of chemical conversion in the welding zone under the influence of ultrasonic vibrations were examined. Variation in width of heat-affected zone of weld seam was measured. The seam strength of ultrasonic weld seam compared with that of conventional seams, and superior seam strength yielding parametric levels were assessed. The parametric influence of both joining techniques on seam quality and their tendencies in the relationship were analyzed statistically. The weld seam strength (1256.392 and 2116.93 N/50 mm) was optimized numerically and identified its trend with the variation of the weld seam. The discovered relationship led to the conclusion that the variation in the weld seam can be used to estimate the tensile strength of the weld seam through the developed effective numerical model as a non-destructive testing method, and its outcome was successful as a destructive testing method. The result shows that the ultrasonic weld seam provided a higher tensile strength ( > 75%) than the conventional seam for both evaluated welding widths and obtained statistically significant results.
A study of polyvinylchloride-coated woven polyester fabric welding potential was conducted using continuous ultrasonic welding machines. The effect of cooling air, anvil wheel status, anvil wheel width, material surface contact, and welding gap on seam strength was studied. Three main welding parameters with different levels were selected based on 5 and 10 mm welding widths using old and new anvil wheels with and without cooling air. A lapped type of seam was applied under full factorial design. A microstructure was captured to examine the formation of welding joints, and seam tensile properties were determined. Comparative analysis of comparable welding parameters was analyzed for a gap against pressure and amplitude against power. The actual weld phenomenon was also analyzed based on the recorded machine parameters. The results showed that auxiliary parameters had a significant effect on seam strength. A microscopic image of a welded seam indicated that cooling air reduced the number and size of holes produced. Weld seam with controlled pressure or power provided higher seam strength than that of the controlled gap or amplitude. The actual phenomenon of welding parameters was important to evaluate weld seam quality, whereby the obtained results indicated good quality at lower power and pressure.
In the research project presented in this paper, the effects of welding width, pressure force, power, and speed of ultrasonic welding parameters on hydrostatic pressure resistance were examined. A flexible and lightweight PVC-coated hybrid textile material with uniform thickness was used for weather protection purposes. Three main welding parameters at three different levels were selected based on the preliminary test results involving welding widths of 6 and 12 mm. A lapped type of seam was applied for ultrasonic welding and conventional joining techniques. A conventionally sewn zigzag seam was produced using three main factors at two different levels according to the application area. To avoid seam permeability, the conventional seam was sealed with tape by means of hot-air tape welding and subsequently investigated regarding its hydrostatic pressure resistance. The hydrostatic pressure resistance value of the conventional seam was then compared with ultrasonic weld seams of 6 and 12 mm welding width, and its parametric influence on the quality of the seam was analyzed. The result shows that the ultrasonic weld seam with a 12 mm welding width provided a higher hydrostatic pressure resistance than the 6 mm welding width and the conventionally sewn seam. Statistical analyses were also carried out to prove the significant effect of welding process parameters on hydrostatic pressure resistance, whereby the obtained results were statistically significant. A suitable nonlinear numerical model was also developed to predict the hydrostatic pressure resistance.
A series of research has been conducted to analyze the quality of weld seams by non-destructive testing methods. Research on defect analysis using the actual ultrasonic welding phenomenon has not been addressed yet. To ensure a comprehensive quality evaluation, this research estimates the size and location of artificial weld seam defects by the actual ultrasonic welding phenomenon without conventional inspection systems. The welding parameters (power, pressure force, and speed) were carefully selected to ensure optimal bond strength. A superimposed type of seam was produced longitudinally by PVC-coated hybrid textiles in rough to smooth surface contact for two welding groups, using a welding width of 10 mm with an activated cooling air effect. Artificial defects were introduced across the weld seam at five different locations spaced 50 mm apart using Teflon films of 3 and 5 mm width. The actual weld phenomenon of ultrasonic welding process parameters was determined after the recorded machine parameters were converted. The effect of welding process parameters on the seam quality was also analyzed, comparing the weld seam quality between different welding groups and Teflon widths. Based on the discovered graph of the actual welding phenomenon, the location and extent of artificial weld seam defects were estimated. The artificial weld seam defect with a thickness of 0.059 mm at a width of 3.85 mm was estimated at an interval of 50.77 mm using 275 N welding pressure force and 120 W welding power at 2 m min−1 welding speed for 3 mm Teflon width. The results showed that the estimated values closely align with the actual size and position of defects. Overall, this research contributes to the development of a non-destructive testing approach for detecting weld seam defects in ultrasonic welding, emphasizing the importance of these techniques for online inspection and control of weld seam quality.
10 July 2023 in Journal of Advanced Joining Processes
Ultrasonic welding is a universal, clean, and secure alternative joining method. Alternative joining technologies are used increasingly to fulfill specific functional requirements of the seam, such as fluid impermeability to achieve positive bonding during the assembly of technical textiles. In this research, the effect of important ultrasonic welding parameters on peel strength and weld seam thickness was investigated for flexible and lightweight textile material, which is a valuable innovative hybrid textile for technical applications like architectural, construction, and protective textiles. Three main welding parameters with three different levels were selected based on the preliminary test results of 6 and 12 mm welding widths, and a superimposed type of seam was applied. Light scanning microscopic images were used to examine the effective weld locations and their morphology at the joining interface. The parametric influence of ultrasonic welding technique on-seam quality and their tendencies in the relationship were analyzed. Optimized peel strength yielding parametric levels were also assessed numerically. The result shows that the optimal peel strength value was obtained at a welding speed of 2.318 m/min, power of 119.382 W, and pressure force of 349.729 N for a 12 mm welding width. The weld seam thickness had an inverse relationship with the peel strength, and a higher amount of thickness was reduced to 12 mm welding width than 6 mm. Microscopic cross-sectional image of weld seam indicated that a compressed yarn between the coating material at higher welding power and pressure force in lower welding speed. A nonlinear quadratic numerical model was developed to predict the peel strength, and their results were close to the regressed diagonal line against the actual points. The statistical analysis was carried out to show the significant effect of process parameters on peel strength, whereby the obtained results were statistically significant.