Nadine Yehya Yehya

Dr. Nadine Yehya Yehya


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 April 2025 in Buildings
Verified
Journal Article
Open access
PDF file
Nadine Yehya YehyaNadine Yehya Yehya
Nadine Yehya Yehya
CMChantal Maatouk
Chantal Maatouk
Hussein CharafHussein Charaf
Hussein Charaf
The building sector is a major global energy consumer, particularly in Lebanon, where heating and air conditioning demand remains high. Integrating Phase Change Material (PCM) into building envelopes presents a promising solution for latent heat storage and enhanced energy efficiency. This study investigates the optimal wall configurations for improved thermal performance using PCM in two Lebanese regions: Beirut and Bekaa. Using ANSYS Fluent, various wall configurations were analyzed to determine the most effective placement of PCM. The optimal configurations were then evaluated in DesignBuilder to estimate energy savings. Results indicate that in Bekaa, external PCM and insulation provide the best performance due to strong dependence on external conditions, whereas in Beirut, internal PCM and insulation are more effective. PCM implementation in both regions significantly reduces energy consumption, with Bekaa proving more advantageous as it does not require additional cooling mechanisms. This research underscores the potential of PCM as a viable strategy for enhancing energy efficiency in building envelopes, with relevance to the climatic conditions of Beirut and Bekaa.

20 April 2025
Verified
Conference Paper
Closed access
Nadine Yehya YehyaNadine Yehya Yehya
Nadine Yehya Yehya
FHFarah Homsi
Farah Homsi
CMChantal Maatouk
Chantal Maatouk
Sustainable design and construction have become essential in recent decades. The use of construction materials, particularly aggregates from recycled construction and demolition waste, has contributed to addressing challenges such as the scarcity of natural resources, the high cost of landfilling, and the increased demand for aggregates. This paper examines the production of non-load bearing hollow blocks using Recycled Concrete Aggregates (RCA) and Recycled Masonry Aggregates (RMA) derived from demolition waste following the Beirut Port blast. Five different mixtures were prepared by varying the replacement rates of Natural Aggregates (NA) with recycled aggregates (RCA or RMA): Mix 0 (reference mix with NA only), Mix 1 (30% RCA), Mix 2 (60% RCA), Mix 3 (10% RMA), and Mix 4 (20% RMA). Mechanical tests were conducted along with thermal testing using a customized Simple Hot Box with the Heat Flow Meter method. The results showed that Mix 2 (60% RCA) and Mix 3 (10% RMA) achieved the required compressive strength, while Mix 1 (30% RCA) and Mix 4 (20% RMA) required an additional 10% cement to meet the strength requirements. The thermal properties of hollow blocks containing varying proportions of RCA and RMA demonstrated improved thermal resistance.

5 July 2023
Verified
Conference Paper
Closed access
Nadine Yehya YehyaNadine Yehya Yehya
Nadine Yehya Yehya
CMChantal Maatouk
Chantal Maatouk
The continuous growth in building sector in addition to the required measures for energy efficiency in building envelopes have increased the need for ecological building materials. In order to decide if the newly developed materials are appropriate for building envelopes, their thermal transmittance should be tested. There are several methods for thermal characterization of building envelopes whether in lab or in situ, however most of them are expensive or have several limitations. To overcome these burdens, it becomes necessary to develop a required experimental setup with simple ways to achieve the desired purpose within certain acceptable errors. The following article describes the design and construction of a low-cost Simple Hot Box for thermal characterization of building envelopes, by means of Heat Flow Meter (HFM) method. The setup was designed and simulated using a computational fluid dynamic software CFD, and then it was constructed at the laboratory of Saint Joseph University, Lebanon. The thermal conductance of a commercial material was found and compared to its known values. The results were close with a little relative error indicating the ability to adopt this apparatus for preliminary evaluation of thermal transmittance of newly developed building materials with little cost and time.

24 September 2025
Verified
Conference Paper
Closed access
JGJulien Bou Gebrael
Julien Bou Gebrael
Nadine Yehya YehyaNadine Yehya Yehya
Nadine Yehya Yehya
SSSabine Saad
Sabine Saad
ABAnissia Beainy
Anissia Beainy
The CLACC (Lebanese Communities on Adaptation to Climate Change) guide is an essential reference to support Lebanese municipalities in mainstreaming climate issues into their local policies. It offers a structured methodology to identify vulnerabilities, assess risks, and implement adaptation strategies tailored to Lebanon's territorial specificities. Through participatory approaches and local case studies, the guide provides communities with practical tools to strengthen infrastructure resilience, preserve natural resources, and improve the quality of life for populations in the face of climate change impacts. By emphasizing sustainable and inclusive solutions, it aims to promote effective and integrated climate governance at the local level.

8 December 2021
Verified
Conference Paper
Closed access
Nadine Yehya YehyaNadine Yehya Yehya
Nadine Yehya Yehya
CMChantal Maatouk
Chantal Maatouk
Reduced energy demands in Low Energy buildings call for advanced building energy modeling that focuses on studying active building systems such as heating, cooling and ventilation, improvement of systems performances, and development of control systems. Modeling and building simulation have expanded to cover different modeling approaches i.e.: detailed physical model, dynamic classical empirical models and hybrid approaches, which are adopted by various simulation tools. This paper uses DesignBuilder with EnergyPlus simulation engine in order to; first, study the impact of efficiency measures on building energy behavior by comparing Low energy residential apartment to a conventional one in Beirut-Lebanon. Second, choose the appropriate energy systems for the studied case characterized by an important cooling demand. Third, study dynamic modeling of Variable Refrigerant Flow (VRF) system in EnergyPlus that is chosen due to its advantages over other systems and its availability in the Lebanese market. Finally concluding that simulation of different energy systems models with different modeling approaches is necessary to investigate the interaction between energy systems and building envelope that affects the total energy consumption of Low Energy buildings.