Nagendra G. Tanikella

Dr. Nagendra G. Tanikella

Mechanical Engineering, University of Idaho, Moscow, Idaho, USA
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2017 in Additive Manufacturing
Verified
Journal Article
Closed access
Nagendra G. TanikellaNagendra G. Tanikella
Nagendra G. Tanikella
BWBen Wittbrodt
Ben Wittbrodt
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce

20 May 2019 in Materials
Verified
Journal Article
Open access
PDF file
MRMatthew J. Reich
Matthew J. Reich
AWAubrey Woern
Aubrey Woern
Nagendra G. TanikellaNagendra G. Tanikella
Nagendra G. Tanikella
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce
Past work has shown that particle material extrusion (fused particle fabrication (FPF)/fused granular fabrication (FGF)) has the potential for increasing the use of recycled polymers in 3D printing. This study extends this potential to high-performance (high-mechanical-strength and heat-resistant) polymers using polycarbonate (PC). Recycled PC regrind of approximately 25 mm2 was 3D printed with an open-source Gigabot X and analyzed. A temperature and nozzle velocity matrix was used to find useful printing parameters, and a print test was used to maximize the output for a two-temperature stage extruder for PC. ASTM type 4 tensile test geometries as well as ASTM-approved compression tests were used to determine the mechanical properties of PC and were compared with filament printing and the bulk virgin material. The results showed the tensile strength of parts manufactured from the recycled PC particles (64.9 MPa) were comparable to that of the commercial filament printed on desktop (62.2 MPa) and large-format (66.3 MPa) 3D printers. Three case study applications were investigated: (i) using PC as a rapid molding technology for lower melting point thermoplastics, (ii) printed parts for high temperature applications, and (iii) printed parts for high-strength applications. The results show that recycled PC particle-based 3D printing can produce high-strength and heat-resistant products at low costs.

25 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
HLHelen Little
Helen Little
Nagendra G. TanikellaNagendra G. Tanikella
Nagendra G. Tanikella
MRMatthew J. Reich
Matthew J. Reich
MFMatthew J. Fiedler
Matthew J. Fiedler
SSsamantha snabes
samantha snabes
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce
This study explores the potential to reach a circular economy for post-consumer Recycled Polyethylene Terephthalate (rPET) packaging and bottles by using it as a Distributed Recycling for Additive Manufacturing (DRAM) feedstock. Specifically, for the first time, rPET water bottle flake is processed using only an open source toolchain with Fused Particle Fabrication (FPF) or Fused Granular Fabrication (FGF) processing rather than first converting it to filament. In this study, first the impact of granulation, sifting, and heating (and their sequential combination) is quantified on the shape and size distribution of the rPET flakes. Then 3D printing tests were performed on the rPET flake with two different feed systems: an external feeder and feed tube augmented with a motorized auger screw, and an extruder-mounted hopper that enables direct 3D printing. Two Gigabot X machines were used, each with the different feed systems, and one without and the latter with extended part cooling. 3D print settings were optimized based on thermal characterization, and both systems were shown to 3D print rPET directly from shredded water bottles. Mechanical testing showed the importance of isolating rPET from moisture and that geometry was important for uniform extrusion. The mechanical strength of 3D-printed parts with FPF and inconsistent flow is lower than optimized fused filament, but adequate for a wide range of applications. Future work is needed to improve consistency and enable water bottles to be used as a widespread DRAM feedstock.

1 June 2020 in Resources, Conservation and Recycling
Verified
Journal Article
Closed access
SDSamantha C. Dertinger
Samantha C. Dertinger
NGNicole Gallup
Nicole Gallup
Nagendra G. TanikellaNagendra G. Tanikella
Nagendra G. Tanikella
Marzio GrassoMarzio Grasso
Marzio Grasso
SVSamireh Vahid
Samireh Vahid
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce

1 February 2021 in Journal of Cleaner Production
Verified
Journal Article
Closed access
WLWilliam Lytle
William Lytle
TMTheresa K. Meyer
Theresa K. Meyer
Nagendra G. TanikellaNagendra G. Tanikella
Nagendra G. Tanikella
LBLaurie Burnham
Laurie Burnham
JEJulie Engel
Julie Engel
JPJoshua M. Pearce
Joshua M. Pearce

1 October 2020 in HardwareX
Verified
Journal Article
Open access
APAliaksei Petsiuk
Aliaksei Petsiuk
Nagendra G. TanikellaNagendra G. Tanikella
Nagendra G. Tanikella
SDSamantha Dertinger
Samantha Dertinger
APAdam Pringle
Adam Pringle
SOShane Oberloier
Shane Oberloier
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce
This study describes the development of a simple and easy-to-build portable automated bag valve mask (BVM) compression system, which, during acute shortages and supply chain disruptions can serve as a temporary emergency ventilator. The resuscitation system is based on the Arduino controller with a real-time operating system installed on a largely RepRap 3-D printable parametric component-based structure. The cost of the materials for the system is under $170, which makes it affordable for replication by makers around the world. The device provides a controlled breathing mode with tidal volumes from 100 to 800 mL, breathing rates from 5 to 40 breaths/minute, and inspiratory-to-expiratory ratio from 1:1 to 1:4. The system is designed for reliability and scalability of measurement circuits through the use of the serial peripheral interface and has the ability to connect additional hardware due to the object-oriented algorithmic approach. Experimental results after testing on an artificial lung for peak inspiratory pressure (PIP), respiratory rate (RR), positive end-expiratory pressure (PEEP), tidal volume, proximal pressure, and lung pressure demonstrate repeatability and accuracy exceeding human capabilities in BVM-based manual ventilation. Future work is necessary to further develop and test the system to make it acceptable for deployment outside of emergencies such as with COVID-19 pandemic in clinical environments, however, the nature of the design is such that desired features are relatively easy to add using protocols and parametric design files provided.