Namwuk Baek

Dr. Namwuk Baek

Department of Physic, Sungkyunkwan, Suwon, Gyeonggi, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2023 in Investigative and Clinical Urology
Verified
Journal Article
Open access
PDF file
JCJae Hoon Chung
Jae Hoon Chung
NBNamwuk Baek
Namwuk Baek
HLHyuna Lim
Hyuna Lim
CSChanyong Seo
Chanyong Seo
YCYong Ki Cho
Yong Ki Cho
DHDeok Hyun Han
Deok Hyun Han
Chung JH, et al. Investig Clin Urol. 2023 Mar;64(2):175-181. https://doi.org/10.4111/icu.20220393

2 September 2024 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Closed access
CSChanyong Seo
Chanyong Seo
NBNamwuk Baek
Namwuk Baek
YPYoonsoo Park
Yoonsoo Park
HLHyuna Lim
Hyuna Lim
SLSungwoo Lee
Sungwoo Lee
DJDonggeun Jung
Donggeun Jung
As the semiconductor industry has continuously reduced the integrated circuit (IC) chip size, a resistance-capacitance (RC) delay emerged, causing deterioration of the chip performance. To reduce the RC delay, low dielectric constant (low-k) films with suitable mechanical strengths have been adopted as intermetal dielectrics (IMDs). In this study, low-k plasma-polymerized diethoxymethylsilane (ppDEMS) films were fabricated by plasma-enhanced chemical vapor deposition of the DEMS precursor with a flow rate ratio of the DEMS precursor to helium (He) carrier gas (DEMS/He FRR) as a key parameter. As the DEMS/He FRR increased, the refractive index was reduced from 1.401 to 1.386, and the k value decreased from 2.77 to 2.10. From high-resolution scans of C1s, O1s, and Si2p peaks of X-ray photoelectron spectroscopy, the carbon contents increased, and the oxygen contents decreased, along with a decrease in the film density. With the increased DEMS/He FRR, hardness decreased from 2.5 to 1.8 GPa, and elastic modulus decreased from 17.08 to 11.50 GPa. Leakage current densities for all the ppDEMS films were less than 10−7 A cm−2 at 1 MV cm−1. The ppDEMS films could be suggested as the IMDs according to their electrical and mechanical performance.

28 June 2023 in Materials
Verified
Journal Article
Open access
PDF file
NBNamwuk Baek
Namwuk Baek
YPYoonsoo Park
Yoonsoo Park
HLHyuna Lim
Hyuna Lim
JCJihwan Cha
Jihwan Cha
TJTaesoon Jang
Taesoon Jang
DJDonggeun Jung
Donggeun Jung
As semiconductor chips have been integrated to enhance their performance, a low-dielectric-constant material, SiCOH, with a relative dielectric constant k ≤ 3.5 has been widely used as an intermetal dielectric (IMD) material in multilevel interconnects to reduce the resistance-capacitance delay. Plasma-polymerized tetrakis(trimethylsilyoxy)silane (ppTTMSS) films were created using capacitively coupled plasma-enhanced chemical vapor deposition with deposition plasma powers ranging from 20 to 60 W and then etched in CF4/O2 plasma using reactive ion etching. No significant changes were observed in the Fourier-transform infrared spectroscopy (FTIR) spectra of the ppTTMSS films after etching. The refractive index and dielectric constant were also maintained. As the deposition plasma power increased, the hardness and elastic modulus increased with increasing ppTTMSS film density. The X-ray photoelectron spectroscopy (XPS) spectra analysis showed that the oxygen concentration increased but the carbon concentration decreased after etching owing to the reaction between the plasma and film surface. With an increase in the deposition plasma power, the hardness and elastic modulus increased from 1.06 to 8.56 GPa and from 6.16 to 52.45 GPa. This result satisfies the hardness and elastic modulus exceeding 0.7 and 5.0 GPa, which are required for the chemical–mechanical polishing process in semiconductor multilevel interconnects. Furthermore, all leakage-current densities of the as-deposited and etched ppTTMSS films were measured below 10−6 A/cm2 at 1 MV/cm, which is generally acceptable for IMD materials.

1 March 2026 in Biointerphases
Verified
Journal Article
Closed access
CSChanyong Seo
Chanyong Seo
SKSang-Soon Kim
Sang-Soon Kim
HPHeonyong Park
Heonyong Park
YSYoungsik Seo
Youngsik Seo
MKMyounghyeon Kyoung
Myounghyeon Kyoung
DJDonggeun Jung
Donggeun Jung
Biliary stents are medical devices inserted into the bile duct to treat biliary strictures. However, inserted stents can become occluded within a few months after placement. In this study, the inner surface of a polyethylene (PE) tube was plasma-treated with helium (He), nitrogen (N2), oxygen (O2), and their gas mixtures to improve resistance to stent occlusion. Surface characteristics were analyzed by water contact angle (WCA) and x-ray photoelectron spectroscopy (XPS) measurements. In the WCA results, bare PE without plasma treatment was the most hydrophobic at 100.7°, whereas PE(He) plasma-treated with He gas became the most hydrophilic at 26.1°. XPS deconvolution analysis revealed that the PE(He) and PE(He/N2) contained a considerable proportion of O 1s present as amide (–CONH–) groups exceeding 40%, whereas the other samples had proportions below 7%. The resistance to stent occlusion was verified through microbial and cancer cell adhesion assays. In the microbial adhesion assay, Escherichia coli (E. coli) was used, and PE(He) showed a statistically significant reduction in E. coli growth compared to bare PE. Inhibition of cancer cell adhesion was the most pronounced in PE(He) and PE(He/N2), with reductions in fluorescence intensities of 75.5% and 81.5%, respectively. Overall, both surface hydrophilization and amidation were found to be effective in inhibiting the adhesion of organic contaminants. It was proposed that plasma surface treatment has the potential to improve resistance to biliary stent occlusion.

12 March 2025 in Journal of Materials Research
Verified
Journal Article
Closed access
PDF file
CSChanyong Seo
Chanyong Seo
JCJeongbeom Choi
Jeongbeom Choi
KBKyubeom Bae
Kyubeom Bae
JKJaeyeon Kim
Jaeyeon Kim
NBNamwuk Baek
Namwuk Baek
DJDonggeun Jung
Donggeun Jung