The Incremental Dynamic Analysis (IDA) assesses the global collapse capacity of a structure by plotting its maximum inelastic response, obtained through a non-linear time-history analysis, versus the scaled intensity of different input earthquakes. The seismic intensity is often measured through the spectral acceleration at the fundamental elastic period. However, this can produce highly variable results. An alternative method is presented in this paper that relies on the elongated period, calculated either from the Fourier spectrum of the acceleration at a target building point (inelastic peak period) or from a smooth Fourier spectrum (inelastic smooth peak period). By referring to a reference reinforced concrete building and to a set of 10 spectrum-consistent earthquakes, the paper presents the results of a wide investigation. First, the variation in the elongated period as a function of the seismic intensity is discussed. Then, the effectiveness of the proposed method is assessed by comparing the IDA curves to those obtained through the elastic period or through approximate values of the elongated period given in the literature. The results show that the alternative IDA procedure generates curves with less-dispersed collapse thresholds. A statistical analysis shows significant improvements in the results when the inelastic smooth peak period is adopted.
Structural engineers commonly design superstructures as fixed at the base and transmit the reactions to the infrastructure in order to design the foundation system and estimate the displacement of the soil while disregarding the change in seismic response that this induces. In this article, the foundation system was transformed into equivalent springs, and the seismic response in the linear range was compared and quantified, obtaining results such as increased periods, increased amounts of steel reinforcement in beams (between 7% and 25%) and columns (between 29% and 39%), an increase in the number of stirrups per linear meter (between 3% and 11% in columns and between 5% and 45% in beams) and drifts (between 1% and 14%), and a decrease in basal shear (up to 20%), which directly affects the design of the structure. This study concludes that the inclusion of the soil-structure interaction is necessary for structural design in the linear range.
The following article presents the elaboration and results obtained from a 3D finite element, of the 8-node hexahedron type with 6 degrees of freedom (DOF) per node (48 DOF per element) based on third degree Hermitian polynomials, and of a 2-node structural element, with 6 DOF per node (12 DOF per element), based on third degree Hermitian polynomials and the theory of Timoshenko for beams. This article has two purposes; the first one is the formulation of a finite element capable of capturing bending effects, and the second one is to verify whether it is possible to obtain the deformation of the beam’s cross section of a structural member of the beam type, based on the deformations of its axis. The results obtained showed that the 8-node hexahedron FE was able to reproduce satisfactory results by simulating some cases of beams with different contour and load conditions, obtaining errors between 1% and 4% compared to the ANSYS software, educational version. Regarding the structural element of the beam type, it reproduced results that were not as precise as the FE Hexa 8, presenting errors of between 6% and 7% with regard to the axis but with error rounding between 10% and 20%.
This article discusses the use of green roofs as rainfall water storage in its soil matrix. The methodology is analytical based on mathematical models, where runoff produced in an urban area is compared with current conditions of ordinary roofs with ceramic or bituminous materials as the original scenario, against another where green roofs are used. The study area is located in the Palavecino municipality of Lara state in Venezuela, in the flood zone of Quebrada Tabure. In this research, a quantitative comparison of the direct runoff hydrographs of the proposed scenarios was used, obtaining as a main result the reduction of runoff between 60% and 80% according to the period of return. An interesting point of this research was the incorporation of the routing of hydrographs on the roofs, reducing even more the peak flow over 90%, and delaying the peak time of the generated hydrographs between 10 and 12 minutes while the total duration of the hydrographs increase more than three times.
26 March 2025 in Bulletin of Earthquake Engineering
El uso de herramientas informáticas para resolver cálculos en cualquier área de estudio es esencial para reducir el tiempo dedicado a realizarlas, dando lugar a la inversión de tiempo en el análisis del problema para un número "n" de soluciones al problema propuesto, pudiendo realizar iteraciones múltiples hasta alcanzar un resultado óptimo. El objetivo de este artículo es utilizar una de las herramientas informáticas más simples, como el programa Microsoft Excel, para crear un código en Visual Basic que permita la resolución de estructuras planas, sujetas a fuerzas de corte, fuerzas axiales y momentos flectores, calculando así las reacciones y desplazamientos en los nodos de la estructura. La macro se basó en el análisis de estructuras con el método de rigidez directa, donde se crearon códigos para obtener la matriz de rigidez de cada elemento, la matriz de rigidez global de la estructura ensamblada a partir de la matriz de rigidez de cada elemento, la matriz de fuerzas de empotramiento, la matriz de fuerzas nodales, y la matriz de desplazamientos de cada nodo. Cada una de las matrices se muestran en una hoja de cálculo, de modo que para fines académicos, el usuario podrá visualizar cada una de las matrices.