Thin films of lead sulfide (PbS) are being extensively used for the fabrication of optoelectronic devices for commercial and military applications. In the present work, PbS films were fabricated onto a soda lime glass substrate by using an electron beam (e-beam) evaporation technique at a substrate temperature of 300 °C. Samples were annealed in an open atmosphere at a temperature range of 200–450 °C for 2 h. The deposited films were characterized for structural, optical, and electrical properties. Structural properties of PbS have been studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), and Rutherford backscattering spectrometry (RBS). The results of XRD showed that the PbS thin film was crystalline in nature at room temperature with cubic crystal structure (galena) and preferential (111) and orientation (022). The morphology of the thin films was studied by FESEM, which also showed uniform and continuous deposition without any peel-off and patches. EDS analysis was performed to confirm the presence of lead and sulfur in as-deposited and annealed films. The thickness of the PbS film was found to be 172 nm, which is slightly greater than the intended thickness of 150 nm, determined by RBS. Ultraviolet-Visible-Near-Infrared (UV-Vis-NIR) spectroscopy revealed the maximum transmittance of ~25% for as-deposited films, with an increase of 74% in annealed films. The band gap of PbS was found in the range of 2.12–2.78 eV for as-deposited and annealed films. Hall measurement confirmed the carriers are p-type in nature. Carrier concentration, mobility of the carriers, conductivity, and sheet resistance are directly determined by Hall-effect measurement. The as-deposited sample showed a conductivity of 5.45 × 10−4 S/m, which gradually reduced to 1.21 × 10−5 S/m due to the composite nature of films (lead sulfide along with lead oxide). Furthermore, the present work also reflects the control of properties by controlling the amount of PbO present in the PbS films which are suitable for various applications (such as IR sensors).
V2O5 thin films have made impressive progress in the development of resistive microbolometers. The challenging parameters for microbolometers are the active material selection and the deposition methods. It might be a more promising way to achieve a good performance of the devices. The present work deals with the V2O5 thin films fabricated on soda lime glass substrates by using e-beam evaporation and magnetron sputtering techniques at a substrate temperature of 200 °C. Afterward, samples were annealed at 300 and 400 °C for 1 h to obtain uniform and stoichiometric thin films. X-ray Diffraction (XRD) showed that the thin films deposited by magnetron sputtering were amorphous in nature, even after annealing at elevated temperatures; however, the thin films fabricated by the electron beam evaporation technique show crystalline nature, which was improved by annealing. XRD also revealed various mixed phases of VOx in electron beam-deposited films. Optical properties were determined using UV-Visible spectroscopy, which showed a decrease in transmittance from 81% down to 57% by increasing the annealing temperature. Similarly, the band gap calculated for electron beam evaporated and magnetron sputtered V2O5 thin films was observed in the range of 1.41 to 2.25 eV. Rutherford backscattering (RBS) was performed to determine the thickness and composition of the films. Slight variations have been observed in intended and deposited thicknesses of films fabricated by e-beam and sputtering techniques. Structural properties revealed by Field Emission Scanning Electron Microscope (FESEM) were found to be the uniform, compact and dense surface of the as-deposited and 300 °C annealed samples. However, annealing at 400 °C changed the surface morphology into nanorods in e-beam and plate-like structures in the sputtered film. EDS proved the elemental concentration of vanadium and oxygen in these V2O5 thin films. Electrical properties were investigated using the Hall measurement technique which showed better conductivity of sputtered films than e-beam deposited films. It can be concluded that the cost-effective and reliable microbolometers infrared (IR) sensors can be fabricated using annealed sputtered films.
The quality of the final product principally relies on preharvest and postharvest factors of fruits, especially plum. These factors include orchard health, pruning operation, application of fertilizers, irrigation of plants, spraying of fungicides, weed control, genotypic variation, maturity stage of plant, time and method of harvesting, sorting and grading, application of edible coatings, use of packaging and packaging materials, storage facilities and others. These factors mainly contribute to the compositional changes, initial microbial load and physical properties of fruit. This chapter will highlight the effect of preharvest and postharvest factors on the final quality of plum fruit.