Thermoplastic starch composites have attracted significant attention due to the rise of environmental pollutions induced by the use of synthetic petroleum-based polymer materials. The degradation of traditional plastics requires an unusually long time, which may lead to high cost and secondary pollution. To solve these difficulties, more petroleum-based plastics should be substituted with sustainable bio-based plastics. Renewable and natural materials that are abundant in nature are potential candidates for a wide range of polymers, which can be used to replace their synthetic counterparts. This paper focuses on some aspects of biopolymers and their classes, providing a description of starch as a main component of biopolymers, composites, and potential applications of thermoplastics starch-based in packaging application. Currently, biopolymer composites blended with other components have exhibited several enhanced qualities. The same behavior is also observed when natural fibre is incorporated with biopolymers. However, it should be noted that the degree of compatibility between starch and other biopolymers extensively varies depending on the specific biopolymer. Although their efficacy is yet to reach the level of their fossil fuel counterparts, biopolymers have made a distinguishing mark, which will continue to inspire the creation of novel substances for many years to come.

This research was done to optimize the influence of various egg albumin (EA) concentrations of 2, 4, and 6% as a foaming agent and whipping times of 5, 10, and 15 minutes, on physicochemical and antioxidant properties of plum powder produced using response surface methodology (RSM). Physical properties of the foam such as density, porosity, and expansion were determined. After drying and powder manufacturing, physical properties, namely, the water absorption index (WAI) and water solubility index (WSI), as well as chemical characteristics such as pH, titratable acidity, and browning index, were assessed. Finally, antioxidant capabilities such as the total phenol content (TPC), DPPH scavenging activity, beta carotene, and total flavonoid content (TFC) were measured. According to the findings, both whipping duration and EA concentration had a substantial effect on the foam forming characteristics. Foam expansion increased significantly with EA concentration and whipping time increase, but foam density exhibited an inverse relationship as expected. Increases in EA concentration and whipping duration both raised pH values whereas titratable acidity exhibited an inverse tendency as variable quantity rose. The browning index dropped as EA concentration increased. Antioxidant qualities were retained in dried sample powder as compared with the fresh sample, and they were also altered by variable changes. Overall, a 4% EA concentration for 10 to 15 minutes produced the best dehydration effects with the most antioxidant retention.

Hard fats, obtained from liquid oils by different fat modification techniques, are composed of high-melting-point triacylglycerols (TAGs) that can be used as alternatives to improve the functional characteristics of lipid systems. These low‐cost industrial products are regarded as raw materials in lipid technology. They can behave as modifiers in crystallization processes, acting as preferential nuclei for ordering crystal lattices and inducing specific polymorphic patterns because of their homogeneous TAGs. Adding hard fats, such as mango, illipe, kokum, sal, shea, rambutan, palm oil, palm kernel oil, and sunflower oil, into other oils is beneficial as it increases their compatibility for uses in fat-based products, especially confectionery products. The addition of hard fats has a significant effect on the rate of crystallization, significantly decreasing the induction time for nucleation and leading to a higher hardness, and increases the thermal resistance for applications in fat-based products. The aim of this article is to review the changes in the physicochemical and thermal properties of hard fats and their mixtures obtained by fractionation, enzymatic interesterification and blending, which broaden their applicability in the food industry.

Urea is naturally present in milk, yet urea is added intentionally to increase milk’s nitrogen content and shelf life. In this study, a total of 50 Ultra heat treatment (UHT) milk samples were spiked with known urea concentrations (0–5 w/v%). Attenuated total reflectance–Fourier transform infrared (ATR-FTIR) spectroscopy with principal component analysis (PCA), discriminant analysis (DA), and multiple linear regression (MLR) were used for the discrimination and quantification of urea. The PCA was built using 387 variables with higher FL > 0.75 from the first PCA with cumulative variability (90.036%). Subsequently, the DA model was built using the same variables from PCA and demonstrated the good distinction between unadulterated and adulterated milk, with a correct classification rate of 98% for cross-validation. The MLR model used 48 variables with p-value < 0.05 from the DA model and gave R² values greater than 0.90, with RMSE and MSE below 1 for cross-validation and prediction. The DA and MLR models were then validated externally using a test dataset, which shows 100% correct classification, and the t-test result (p > 0.05) indicated that the MLR could determine the percentage of urea in UHT milk within the permission limit (70 mg/mL). In short, the wavenumbers 1626.63, 1601.98, and 1585.5534 cm⁻¹ are suitable as fingerprint regions for detecting urea in UHT milk.

Green honey is exclusively available on the island of Banggi in Sabah, and its uniqueness sees the commodity being sold at a high market price. Therefore, green honey is prone to adulteration by unscrupulous individuals, possibly compromising the health of those consuming this food commodity for its curative properties. Moreover, an established standard for reducing sugar in green honey is unavailable. Ipso facto, the study aimed to profile green honey’s physical and chemical properties, such as its pH, moisture content, free acidity, ash content, electroconductivity, hydroxymethylfurfural (HMF), total phenolic content, total flavonoid content, DPPH, colour, total sugar content, total protein content, and heavy metals as well as volatile organic compounds, the data of which are profoundly valuable in safeguarding consumers’ safety while providing information for its quality certification for local consumption and export. The results revealed that the honey’s physicochemical profile is comparable to other reported kinds of honey. The honey’s naturally green colour is because of the chlorophyll from the nectar from various flowers on the island. The raw honey showed free acidity between 28 and 33 Meq/100 g, lower than the standard’s 50 Meq/100 g. The hydroxymethylfurfural content is the lowest compared to other reported honey samples, with the total phenolic content between 16 and 19 mg GAE/100 g. The honey’s reducing sugar content is lower (~37.9%) than processed ones (56.3%) because of water removal. The protein content ranged from 1 to 2 gm/kg, 4- to 6-fold and 2-fold higher than local and manuka honey, respectively. The exceptionally high content of trans-4-hydroxyproline in raw honey is its source of collagen and other healing agents. Interestingly, low levels of arsenic, lead, nickel, cadmium, copper, and cobalt were detected in the honey samples, presumably due to their subterranean hives. Nevertheless, the honey is fit for general consumption as the concentrations were below the maxima in the Codex Alimentarius Commission of 2001.