The insufficiency of energy supply and availability remains a significant global energy challenge. This work proposes a novel approach to addressing global energy challenges by testing the supercritical property and conversion of low-temperature thermal heat into useful energy. It introduces a combined-cascade steam-to-steam trigeneration cycle integrated with vapour absorption refrigeration (VAR) and district heating systems. Energetic and exergetic techniques were applied to assess irreversibility and exergetic destruction. At a gas turbine power of 26.1 MW, energy and exergy efficiencies of 76.68% and 37.71% were achieved, respectively, while producing 17.98 MW of electricity from the steam-to-steam driven cascaded topping and bottoming plants. The cascaded plant attained an energetic efficiency of 38.45% and an exergy efficiency of 56.19%. The overall cycle efficiencies were 85.05% (energy) and 77.99% (exergy). More than 50% of the plant’s lost energy came from the combustion chamber of the gas turbine. The trigeneration system incorporated a binary NH₃–H₂O VAR system, emphasizing its significance in low-temperature energy systems. The VAR system achieved a cycle exergetic efficiency of 92.25% at a cooling capacity of 2.07 MW, utilizing recovered waste heat at 88 °C for district hot water. The recovered heat minimizes overall exergy destruction, enhancing thermal plant performance.

Thermoelectric generators are solid-state devices that convert heat into electricity using the Seebeck effect, when there is a temperature difference across a thermoelectric material. This research designed an experimentally tested a thermoelectric hot air generator using sixteen SP1848-27145 modules in two parallel strings. The system consists of a biomass combustion chamber, hot air exhauster, hot and cold side heat exchangers. Voltage, current and temperatures in the combustion chamber, hot air heat exhauster, hot side heat exchanger and cold side heat sink were measured. The hot air exhauster, hot side heat sink and cold side maximum temperatures are 178.3°C, 69.2°C and 44.5°C respectively yielding an open circuit voltage of 64 V and current of 1.99 A in the course of the experiment. The thermal performance of the designed hot air exhauster, hot side heat exchanger and cold side heat were simulated using ANSYS Fluent, for pictorial representation of their temperature contours.

Power inverters play a crucial role in converting DC voltage and current to AC voltage and current. Its efficient operation relies on effective thermal management of the semiconductor devices, such as the IRF 3205 MOSFET chip which facilitate the switching operations to prevent thermo-mechanical stress that could to failure. This research developed and optimize a heat sink for an IRF 3205 MOSFET chip in a 3.5 KVA power inverter, using the Particle Swarm Optimization technique and experimented with a 3.5 KVA 24 V power inverter operating a 1.5HP air-conditioning unit. The heat sink geometry has 26 fins, 4 mm fin thickness, 40 mm fin height, 3 mm fin spacing, 2 mm fin base thickness, 179 mm length, 80 mm width and a thermal resistance of 60.75 °C/W. The thermal performance was evaluated using ANSYS Computational Fluid Dynamics (CFD) and results showed maximum base temperature of 65.85°C and experimental temperature of 64°C after two hours of steady operation dissipating heat of 45W. The results from both numerical and experimental data demonstrate the effectiveness of the optimized heat sink in maintaining the chip's temperature below its maximum working threshold of 170°C.

Direct current to alternating current converter is applied in the conversion of renewable energy such as solar and wind energy. The switching operation is performed by metal oxide semiconductor field effect transistor chips (MOSFET), during th...

Thermoelectric refrigeration achieves cooling through Peltier and Seebeck effect. Heat sinks attached to the hot and cold sides of the thermoelectric module help to efficiently dissipates and absorb heat. This research modelled the temperature profile across a heat sink and its optimization for a thermoelectric refrigeration application. Simulation was carried out using MATLAB to visualize the performance of the heat sink. The optimization was done using FMINCON in MATLAB by setting upper and lower bounds to satisfy space and volume requirement. The optimum values for the hot and cold heat sink geometry obtained using FMINCON tool in OPTIMTOOL box in MATLAB, yields number of fins as 10, fin spacing as 0.003m, the fin thickness as 0.002m and fin length as 0.015m with an optimum temperature of -0.8639.

A thermoelectric generator consists of various thermocouples arranged in series. A voltage is generated when a temperature gradient exists across the junctions of the thermocouples. This research modelled, developed and tested a thermoelectric...