Papa Traore

Dr. Papa Traore

Assoc prof
+1

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 August 2017 in IEEE Sensors Journal
Verified
Journal Article
Closed access
PTPapa Traore
Papa Traore
AAAktham Asfour
Aktham Asfour
JYJean-Paul Yonnet
Jean-Paul Yonnet
CDChristophe P. Dolabdjian
Christophe P. Dolabdjian
In this paper, we propose a general model to evaluate the equivalent magnetic noise for an off-diagonal giant magneto-impedance (GMI) sensor utilizing a software-defined radio (SDR) as a digital receiver. Based on this SDR approach, an analog-to-digital conversion (ADC) of the voltage induced by the sensing element is directly performed. The signal processing is digitally achieved in real time. It includes a digital quadrature demodulation, a decimation, and a filtering. The approach allows to give the key rules for quantifying the white noise level of this digital implementation. The voltage noise spectral density of the ADC and of each SDR stage is given. The white noise level expected by the modeling was in good agreement with the measurements. With a sensing element composed of a 400 turn coil wound around a co-rich GMI wire, equivalent magnetic noise levels of 220 and 4.2 pT/√Hz were obtained at 1 Hz and in the white noise region, respectively. The potential improvement of these performances, allowed by this digital conditioning, as well as limitations is also discussed.

1 March 2018 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
PTPapa Traore
Papa Traore
AAAktham Asfour
Aktham Asfour
JYJean-Paul Yonnet
Jean-Paul Yonnet
CBCédric Boudinet
Cédric Boudinet

16 October 2018 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
Aktham AsfourAktham Asfour
Aktham Asfour
JNJulie Nabias
Julie Nabias
PTPapa Traore
Papa Traore
JYJean-Paul Yonnet
Jean-Paul Yonnet
This paper deals with practical issues and solutions related to the use of the giant magnetoimpedance (GMI) for electrical current measurement. It presents an overview of a full attempt of design and realization of an almost industrial GMI-based current sensor or clamp. The sensor combines dc and ac measurements with the same flexible sensitive element. This paper addresses several practical problems encountered in a real measurement environment. In this context, main attention was paid to the impact of the influence quantities that largely condition the implementation strategies and solutions of the sensor. For the intended industrial application, these influence quantities first include the operating temperature. Its impact on the intrinsic sensor response was investigated in an almost industrial temperature range. Second, bending stress on the sensitive element is another involved influence parameter in the toroidal and flexible structure of the sensor. The effect of this was also characterized. Finally, the third considered influence parameter is the effect of magnetic disturbances. These include the eccentricity of the conductor of interest and the impact of the surrounding magnetic fields such as the earth's field or fields produced by other conductors in close proximity to the sensor. Different strategies of implementation and solutions, taking into account the impact of influence parameters, were proposed and compared. A sensor prototype was realized, and its first performances were given.

8 July 2024 in Measurement Science and Technology
Verified
Journal Article
Closed access
MXMiao Xu
Miao Xu
PTPapa Traore
Papa Traore
Aktham AsfourAktham Asfour
Aktham Asfour
A high sensitivity Magneto-Impedance (GMI) sensor for magnetic communication systems in harsh environments is presented. In this system, the receiving coil of a conventional magnetic communication system is replaced by a high sensitivity GMI sensor and its digital electronic conditioning as well as digital signal processing. The whole architecture of the sensor is described in detail. It achieves two digital amplitude demodulations to recover, in real time, the binary sequence of the message sent by the transmitter. The demonstration and the validation of the reliable functioning of the system are illustrated through the transmission of messages using On-Off-Keying modulation method. The measured equivalent magnetic noise of the sensor was about noise 2   p T / Hz at 60 kHz, which is largely lower than the noise of other potential types of magnetic sensors such as Anisotropic Magneto-Resistive sensors for this application. This noise level suggests a potential higher communication range. When compared with an inductive coil, the developed sensor also presented an almost flat and sufficiently wide bandwidth compatible with magnetic communication. This bandwidth could potentially be extended according to the application.

1 November 2015
Verified
Conference Paper
Closed access
PTPapa Traore
Papa Traore
AAAktham Asfour
Aktham Asfour
JYJean-Paul Yonnet
Jean-Paul Yonnet
This paper deals with the implementation of the Digital-Down-Conversion (DDC) for signal demodulation and processing in Giant Magneto-Impedance (GMI) sensors. In this approach, a direct Analog-to-Digital Conversion (ADC) of the voltage across the sensing element is performed. The signal processing is then digitally done in real time. This processing mainly includes the digital quadrature demodulation, decimation and filtering. A description of the approach and its implementation for the GMI magnetic sensors are given. The system is fully programmable by software. This is why this approach is of great value for the automatic and real-time optimization of various physical parameters that impact the sensitivity and resolution of these sensors.

1 February 2019 in International Journal of Applied Electromagnetics and Mechanics
Verified
Journal Article
Closed access
PDF file
PTPapa Traore
Papa Traore
Aktham AsfourAktham Asfour
Aktham Asfour
JYJean Paul Yonnet
Jean Paul Yonnet
CBCedric Boudinet
Cedric Boudinet
A new fully digital Giant Magneto-Impedance (GMI) sensor is presented. The design combines the off-diagonal configuration of the sensitive element with a real-time digital electronic conditioning based on a Software Defined Radio (SDR). Compared to a conventional implementation of these sensors, the proposed design exhibits key advantages. These include firstly the simplicity of obtaining a quasi-linear sensor response around the zero-field point without making use of a bias magnetic field and an offset cancelling device. Secondly, the potential of integration, the flexibility of reconfiguration as well as the low-noise and high-sensitivity are promising features of the developed concept. Noise performance of 1.8 pT/[ ] was obtained in the white noise region.