Stanislav Popov

Dr. Stanislav Popov

Poltava State Agrarian University, Poltava, Poltavs’ka Oblast’, Ukraine
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2016 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
SKSergey Kravchenko
Sergey Kravchenko
Stanislav PopovStanislav Popov
Stanislav Popov
SGSergey Gnitko
Sergey Gnitko
The research of working pressure of one-piston pump with a combined compensator of pressure pulsations during the operating cycle is carried out. One of the basic gas law in an isothermal process, namely the law of Boyle-Marriott is employed. The law of piston motion which is driven from the crank-connecting rod mechanism (the axis of the crank shaft is made offset downwards relative to the axis of the piston to reduce the magnitude of lateral forces) is used. The piston drive crank rotation angle, the primary pressure in the compensator are taken into account. The research is needed to ensure a stable high-pressure feed of medium (solution) pumped by the pump, with a reduced level of pulsation. The quantitative dependences of the solution volume in the compensator on the piston movement, the solution feed pressure relative to the crank shaft rotation angle, the minimum required amount of total given volume of combined compensator air (it is 0.02m3) are defined.Practical significance of the obtained results of the research is to develop a piston pump design. It provides a stable feed pressure, moderate pulsation level of the solution, which is pumped.

20 June 2018 in International Journal of Engineering & Technology
Verified
Journal Article
Closed access
PDF file
Stanislav PopovStanislav Popov
Stanislav Popov
ASAndrii Shpylka
Andrii Shpylka
SGSergiy Gnitko
Sergiy Gnitko
During the theoretical calculations of the power level consumed by the mortar mixer drive when mixing constructional mortar components, it is proposed to use the movement resistance specific coefficient. The developed method and a series of researches on an experimental test bench allowed to determine its numerical values when mixing cement-sand, lime-sand and complex mortars of various composition and lowability. The interpolated diagram of the consumed power of the band-screw operating device drive has been obtained, which has allowed to understand more deeply the technological process, as well as its characteristic stages and modes.

28 February 2017 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
AVAnatoly Vasilyev
Anatoly Vasilyev
Stanislav PopovStanislav Popov
Stanislav Popov
EVEugene Vasilyev
Eugene Vasilyev
APAnna Pavelieva
Anna Pavelieva
We examined methods of manufacturing profile openings on the metal-cutting machines by the rotational broaching method. Based on the generalized results of analysis of the methods for manufacturing profile openings, we proposed a method of rotational broaching. Bits for drilling machines or screwdrivers are used as the tool. Hardness of the bit is quite high; therefore, making a centering opening in it is difficult. The problem is solved by pressing a transition bushing onto the bit, with a centering opening made in advance. Implementation of the method requires a Morse cone with a welded plate. This allows fixing the rotating centre in a tool carrier. The proposed method makes it possible at minimal financial cost to perform the shaping of profile openings within a wide range of both the shape and nominal dimensions. The method is based on the effect of self-centering and, therefore, does not require preliminary adjustment. Adjusting tool entrance angle is achieved by displacing a transverse support of the lathe and by tool carrier rotation. In addition, in the production of profile opening, its input cone is formed, which provides for easy installation of the wrench to transmit rotational moment without losing load capacity. The studies conducted defined suboptimal values of the input variables that are accepted as rational in the examined technological process of rotational broaching. These are: a tool entrance angle (1.5...2.5 degrees), its supply (0.1...0.3 mm/rev) and the rate of processing (15...25 m/min)

10 January 2022 in EUREKA: Physics and Engineering
Verified
Journal Article
Open access
PDF file
Stanislav PopovStanislav Popov
Stanislav Popov
LFLiliia Frolova
Liliia Frolova
OROleksii Rebrov
Oleksii Rebrov
YNYevheniia Naumenko
Yevheniia Naumenko
ОPОlenа Postupna
Оlenа Postupna
PSPavel Shvets
Pavel Shvets
The object of research in this work was cast iron for machine-building parts, alloyed with Al. The possibility of improving the mechanical properties of cast iron by choosing the optimal Mn – Al combinations, depending on the carbon content in the cast iron, was determined. The study was carried out on the basis of available retrospective data of serial industrial melts by constructing the regression equation for the ultimate strength of cast iron in the three-factor space of the input variables C – Mn – Al. The optimization problem was solved by the ridge analysis method after reducing the dimension of the factor space by fixing the carbon content at three levels: C = 3 %, C = 3.3 %, and C = 3.6 %. It was found that the maximum values of the ultimate strength are achieved at the minimum level of carbon content (C = 3%) and are in the range of values close to 300 MPa. In this case, the Al content is in the range (2.4–2.6) %, and the Mn content is about 0.82 %. With an increase in the carbon content, there is a tendency to a decrease in the content of Mn and Al in the alloy, which is necessary to ensure the ultimate strength close to 300 MPa. The results of the ridge analysis of the response surface also showed that at the upper limit of the carbon content (C = 3.6%), it is not possible to reach the ultimate strength of 300 MPa in the existing range of Mn and Al variation. All solutions are verified for the following ranges of input variables C = (2.94–3.66) %, Mn = (0.5–1.1) %, Al = (1.7–2.9) %. Graphical-analytical descriptions of the optimal Mn – Al ratios are obtained, depending on the actual content of carbon in the alloy, which make it possible to purposefully select the optimal melting modes by controlling the tensile strength of the alloy

23 November 2018 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
AVAnatoly Vasilyev
Anatoly Vasilyev
Stanislav PopovStanislav Popov
Stanislav Popov
IVIevgen Vasyliev
Ievgen Vasyliev
ASAndrii Shpylka
Andrii Shpylka
VVVolodimir Vovchenko
Volodimir Vovchenko
Modernization of the technique for rotary shape-formation of outer profiled surfaces

1 January 2023 in Transactions of Kremenchuk Mykhailo Ostrohradskyi National University
Verified
Journal Article
Closed access
Stanislav PopovStanislav Popov
Stanislav Popov
YLYulia Levchenko
Yulia Levchenko
Yuliia BasovaYuliia Basova
Yuliia Basova
KPKostiantyn Popov
Kostiantyn Popov