The aim of this article is to determine experimentally and numerically the influence of material degradation on the deformation of a paraglider during flight. The presented method regards numerical modeling of pressure distribution over the wing and its effect on paraglider behavior; the considerations are preceded by experiments on three types of Polyamide 6.6 paraglider fabrics, subjected and not subjected to thermal, UV and flexing degradation. Scanning electron microscope (SEM) records allowed to determine the structural characteristics of the analyzed samples. Air permeability and mechanical tests are the input data for the computational simulations. When a pressure drop of 200 Pa is applied, all the analyzed samples are impermeable, except for those damaged by flexing. Thus, flexing damage has the greatest influence on the air permeability change among all considered aging factors. Aging caused by UV radiation has the greatest influence on mechanical properties. No major influence of thermal ageing on the mechanical properties of the considered samples is observed. Safety factors of the considered materials not subjected to degradation range between 3.94 and 6.00. Safety factor of fabric no. 1 subjected to the UV degradation is equal to 1.33; this result does not secure a safe usage of the considered material. The methodology described in this research can help to predict paraglider covering materials’ behavior in flight; it assumes many cases, i.e., applying a new material or the material at any point of its life cycle. Thus, the practical implications of this model supported by numerical methods may result in saving time and cost in producing prototypes, as well as potentially assessing the safety of used wings. Future research activity can introduce the application of different elastic–plastic damage models to determine the paraglider behavior during collapse.
The aim of paper is to determine experimentally and numerically the strength characteristics related to the paraglider wing with Fourier transform infrared spectroscopy of applied materials. The applied method consists in theoretical modeling supplemented by the tests of material parameters. First, the set of 10 lightweight fabrics was selected for the tests; the samples are representative for these structures. The materials were tested using the spectroscopy to determine the FTIR spectra. The samples differ in the content of certain characteristic groups. Air permeability change of the materials was determined for the different pressure drops. The air permeability of almost all the analyzed samples was close to zero with the exception of only one material. The tensile strength and elongation at the break of samples were determined on the testing machine. The paraglider samples were characterized by slightly decreased mechanical properties compared to the parachute fabrics. The material characteristics determined during the tests are the input data for the theoretical analysis. The numerical model of the paraglider wing is based on a 3D geometry from previous research, but the stress, strain, and deformation were determined using the ANSYS Structural program and the finite elements method. To determine the strength correctly, we introduce two basic values: the absolute maximal and the representative values that are the biggest repetitive values of stress, strain, and deformation. The stress value was determined by the main factors: (i) the thinner the material, the bigger the stresses that were accumulated; (ii) the stronger the material, the bigger the stresses that were accumulated. The results are similar for all materials and differ mainly by the values. The biggest stresses were observed inside the material contacting the ribs, whereas the biggest deformation and strain were in the regions between ribs, and the smallest were in the contact areas with the fixed supports. Their highest intensity was observed on the leading edge of the paraglider. We conclude that the obtained stresses were far from the breaking level for the wing.
The operating comfort of a paraglider is created by the aerodynamic parameters as well as the mass and packing volume of the wing. A classic paraglider has upper and lower covers. To reduce the material and manufacturing costs as well as protect the environment, it is possible to introduce a single-skin wing. This article conducts an analysis of a single-skin paraglider covered only with upper panels, whereas the lower cover is applied only at the leading and trailing edges. The analysis is theoretically oriented; aerodynamic and structural calculations were performed using the ANSYS environment. The single-skin structure was evaluated in terms of the predicted behavior during flight and the material’s deformation under the influence of a specified pressure and the overloads acting on it. The results show that developing these structures may influence the creation of models with comparable aerodynamic characteristics to traditional ones. Additionally, the reduced masses and packing volumes of difficult-to-degrade materials are strongly correlated with saving costs and an ecological approach. No corresponding studies were found in the available literature. Thus, this presented analysis may result in a greater understanding and application of this paraglider type.
This study combines experimental conditioning and numerical simulations to evaluate water-induced degradation of swimming-goggle gaskets and their mechanical response under representative loading conditions. Two gasket geometries were modeled, with the flatter profile serving as a reference and the more anatomically representative variant analyzed using finite-element analysis for neoprene, silicone, and SEBS materials of different Shore A hardness under prescribed periorbital pressure distributions. Commercial gaskets were conditioned by static immersion in chlorinated, distilled, and saline water for 20, 30, and 40 days, followed by measurements of Shore A hardness, breaking force, and elongation at break. The numerical results showed that gasket geometry substantially influences the predicted deformation patterns relevant to facial conformability, despite similar overall deformation magnitudes. Prolonged water exposure caused considerable material degradation. The breaking force decreases by approximately 48% after 20 days and by about 50% after 40 days of conditioning, irrespective of the environment. Elongation at break changed by approximately 3–4% in chlorinated and distilled water, whereas saline water caused reductions of approximately 11% after 20 days and 36% after 40 days. Additionally, the hardness of the material drops by about 10–13% after 20 days and subsequently remains almost constant. In the adopted cyclic loading–recovery simulation, silicone exhibited substantially lower residual deformation than SEBS. Overall, the results demonstrate the importance of material selection and geometry optimization and provide a comparative basis for further studies combining environmental conditioning with experimentally calibrated numerical models.
The aim of this study is to present an integrated approach to ski personalization by combining a detailed material and geometric characterization of ski structure with real-time on-slope dynamic performance data. Longitudinal and torsional stiffness were selected as the basic material parameters for a wide range of skis with different application profiles. Acceleration graphs for turns were synchronized with video footage recorded by a drone, which provided real-time monitoring of the skiers’ actual course and facilitated the precise correlation between kinematic data and on-slope performance. To estimate style similarity between different skiers, the Pearson correlation coefficient was utilized due to its robust mathematical properties. Comprehensive analyses helped to finally formulate a multistage ski personalization algorithm.