Our research proposed the prototypes of a Long Range (LoRa) network for agriculture application, which focuses on low-cost and effectiveness with multi-wireless environment sensor nodes in a network. each sensors node consisting of several sensors such as a soil moisture sensor, a temperature and humidity sensor, a raindrops sensor, and a light intensity sensor. The soil moisture sensor has been designed with 4 copper sensing-rods that a longest copper rod act as a ground signal level and other copper sensing-rods using for measures moisture at each soil depth. The different levels of soil depth with respect to the ground surface. A Heltec LoRa esp32 sx1276 acts as a LoRa wireless communication module for long-range environment data transfer. The proposed network that operating with two wireless communication frequency bands, 925.2MHz for node-to-gateway communication and 2.4GHz (WLAN) for gateway-to-cloud communication. Furthermore, the proposed network with three wireless sensor nodes and a single LoRa gateway was experimental. From the experimental results, the sensor node able to environmental sensing and transfer data to the gateway. The environmental data of soil moisture under the ground surface 20cm, 40cm, and 60 cm more than 90% accuracy compared to the standard instrument. Additionally, the LoRa transceiver range is approximately 600 meters (Non-line-of-sight: NLOS) and the LoRa gateway automatically transmits environmental data to the cloud storage every 15 seconds.
In this work, a metasurface-based, 1-bit electronically reconfigurable reflectarray antenna (RRA) is proposed for dual-polarization beam-steering applications. The proposed RRA consists of 16 × 16 Jerusalem cross-shaped unit cells loaded with PIN diodes, which are used as active and reconfigurable devices to generate a reflection phase difference of 180° between their on- and off-states. An optimal focal length to diameter ratio ( f/D ) for the feed antenna is determined to maximize its radiation coverage on the RRA. Microcontroller-based shift registers are used to resolve the complexity of the individual DC bias networks for the PIN diodes. The proposed RRA is designed, fabricated, and measured to evaluate its beam-steering performance. The measurement results show that the proposed RRA can achieve beam-steering of ±60° for x - and y -polarizations in both azimuth and elevation planes. Moreover, the proposed RRA is further verified by full-wave simulations to evaluate its additional functions, such as the generation of sum and difference beams for monopulse radar systems. The proposed RRA is anticipated to have significant potential in areas such as wireless communications, imaging, and radar systems, and is a particularly suitable candidate for reconfigurable intelligent surfaces (RISs) due to its adaptability and capability of dynamically generating different radiation patterns.
Rising concern over livestock emissions and their contribution to climate change demands innovative and cost-effective monitoring solutions. This study introduces and validates a low-cost, LoRa based system for the continuous monitoring of methane (CH4) and carbon dioxide (CO2) emissions in cattle. Unlike previous fixed installation systems, our design features a movable cattle collar equipped with gas sensors, enabling real-time data collection directly from the emission source. The system combines advanced sensor technology with long-range LoRa communication, thereby providing a scalable solution for remote agricultural environments. The experimental results demonstrate that the cattle collar system achieves higher accuracy in detecting CO2 emissions owing to its proximity to the emission source, outperforming fixed systems. The closed feeding slot design showed a comparable accuracy for CH4 detection. Both systems proved capable of reliable data transmission over distances of up to 400 m, making them ideal for large-scale deployments. In terms of cost, our system is significantly more affordable than other commercially available systems. The collar’s portability, low power consumption, and long battery life make it well-suited for continuous monitoring in both indoor and outdoor settings. This study highlights the potential of a movable, low-cost solution for monitoring livestock emissions, contributing to agricultural sustainability and climate change mitigation by providing accurate, real-time data for effective emission management strategies.
The one important in a passive optical network (PON) for high-speed communication is fault detection and fault alert due to the troubles of passive optical fiber or passive optical devices. Any failure of optical devices in the optical link can influence to a huge amount of data loss in the optical network. However, deployment of fault detection and alert devices or systems is extremely limited due to the financial implications and reliability of the devices or systems. Thus, this work proposes a design and implementation of a cost-effective way for detection when an optical link has a fault in a PON. Also, real-time wirelessly alert to a responsible person. This monitoring technique is based on bidirectional light-wave communication with single-core single-mode optical fiber and internet of things (IoT) technology. Which consists of 2 sub-systems namely the transmitter of the optical fiber monitoring system (OFMS-Tx) is located at the optical network unit (ONU). And the receiver of the fiber monitoring system (OFMS-Rx) is located at the optical line terminal (OLT). Both parts operating with microcontrollers, which the OFMS-Tx microcontroller uses for generating a monitoring signal that depends on situations such as normal operation situation or power outage situation. The OFMS-Rx microcontroller act as a monitoring signal decoder for the decision of the OFMS-Tx and optical link situations. Also, OFMS-Rx real-time alerts to responsible person when fault occurring, such as optical link fail or ONU power outage. From experimental results show that the proposed system is automatically working for real-time optical fiber link detection and immediately alert to the responsible person within 11 seconds when a fault occurs. Also, the proposed system could transmit a monitoring signal in the network over a fiber distance of 70 km.
The automatic brightness and soil moisture control system for gerbera smart greenhouse based on internet of thing (IoT) is presented. The automatic brightness control system was designed to detects ambient brightness with a BH1750 sensor. Then, it automatically controls the LED lamps to illuminate an appropriate range for gerbera growth that is between 3000 - 5000 lux. Meanwhile, the automatic soil moisture controller is dedicated to monitoring soil moisture with a fork-type sensor and automatically turns on or off water sprayer when the soil moisture value is lower or higher than the specified value (70 - 80%). Furthermore, the presented system fully operates with an ESP8266 microcontroller integrated with IoT via ISM 2.4GHz wireless communication. The Blynk application is a smart convenient tool that not only graphically displays greenhouse’s data but is also capable of controlling several values of the greenhouse at any time and everywhere. All the greenhouse’s data is real-time online storage via Google sheets for further analysis. From the experimental results, the proposed system works automatically in brightness and soil moisture controlled by only 5.6% of average errors. The water sprayer control system was correctly self-acting turns on and off with respect to demanded values. Also, the greenhouse’s data are automatically stored once an hour on Google sheet based IoT. Additionally, the proposed system is suitable for increasing the convenience of gerbera growers as well as effective scale-up for the huge demand for smart farms.
The Light Emitting Diodes (LEDs) not only giving illumination, but they can transmit information also. So that LED has played an essential role in Visible Light Communication (VLC) technology for indoor short-range data communication. In this paper, several commercial-off-the-shelf (COTS) indoor white-light LED lamps are proposed by considering the performance metrics such as light intensity quality when VLC was adopted, and data transmission efficiency measured in terms of bit error rate (BER). To achieve the proposed VLC system, the system is separated into two parts, first part is a VLC transmitter which combining of an indoor commercial white-light LED lamp, an LED current constant driver, and a data modulation circuit. The second part is a VLC receiver that composes of a BPW34 photodiode (PD) and several signal-amplify circuits. In the experimental setup, the VLC transmitter sending digital data bitstream through optical wireless communication (OWC) channel between 20cm. to 200cm. of distances to a VLC receiver. Then VLC receiver acting as light intensity to the electrical converter. The experimental results showed that, the proposed system is capable of sending data over an OWC channel with 200cm of distance, the BER still less than 10– −3 in condition of without ambiance light noise.