qianhao xiao

Dr. qianhao xiao

Huazhong University of Science and Technology, China

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in Engineering Applications of Computational Fluid Mechanics
Verified
Journal Article
Open access
HLHui Liu
Hui Liu
BJBoyan Jiang
Boyan Jiang
JWJun Wang
Jun Wang
XYXiaopei Yang
Xiaopei Yang
qianhao xiaoqianhao xiao
qianhao xiao
In this study, the unique reverse-flow around the inlet nozzle of a squirrel-cage fan was numerically studied by computational fluid dynamics (CFD), and a non-axisymmetric D-type inlet nozzle was proposed to inhibit it. It is shown that serious back flow develops at the volute tongue when the fan operates at a low flow coefficient that is lower than the best efficiency point. The airflow passing the blade passages in reverse further crosses the impeller, mixing the clearance leakage airflow, and finally blows into the intake chamber near the circumferential position of 150∘. By installing the inlet nozzle along this direction, D-type inlet nozzle schemes with different blockage extent were calculated by CFD. The scheme with a cut distance of 70% of its exit-section radius was chosen as the best design by comprehensively comparing the back flow ratio and fan performance of different working conditions. CFD results illustrated that reverse blowing at the fan entrance was significantly constrained by this D-type inlet nozzle, and the vortex in the inlet chamber correspondingly disappeared. Experimental data illustrated that the new nozzle increased the fan pressure rise under low-flow conditions by about 6% and barely reduced performance at other working points.

3 June 2021 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
PDF file
qianhao xiaoqianhao xiao
qianhao xiao
JWJun Wang
Jun Wang
BJBoyan Jiang
Boyan Jiang
WYWeigang Yang
Weigang Yang
XYxiaopei yang
xiaopei yang
In view of the multi-objective optimization design of the squirrel cage fan for the range hood, a blade parameterization method based on the quadratic non-uniform B-spline (NUBS) determined by four control points was proposed to control the outlet angle, chord length and maximum camber of the blade. Morris-Mitchell criteria were used to obtain the optimal Latin hypercube sample based on the evolutionary operation, and different subsets of sample numbers were created to study the influence of sample numbers on the multi-objective optimization results. The Kriging model, which can accurately reflect the response relationship between design variables and optimization objectives, was established. The second-generation Non-dominated Sorting Genetic algorithm (NSGA-II) was used to optimize the volume flow rate at the best efficiency point (BEP) and the maximum volume flow rate point (MVP). The results show that the design parameters corresponding to the optimization results under different sample numbers are not the same, and the fluctuation range of the optimal design parameters is related to the influence of the design parameters on the optimization objectives. Compared with the prototype, the optimized impeller increases the radial velocity of the impeller outlet, reduces the flow loss in the volute, and increases the diffusion capacity, which improves the volume flow rate, and efficiency of the range hood system under multiple working conditions.

13 April 2022 in Processes
Verified
Journal Article
Open access
PDF file
YDYanyan Ding
Yanyan Ding
JWJun Wang
Jun Wang
BJBoyan Jiang
Boyan Jiang
ZLZhiang Li
Zhiang Li
qianhao xiaoqianhao xiao
qianhao xiao
BXBochao Xie
Bochao Xie
The performance of low-pressure axial flow fans is directly affected by the three-dimensional bending and twisting of the blades. A new blade design method is adopted in this work, where the radial distribution of blade angle and blade bending angle is composed of standard-form rational quadratic Bézier curves. Dendrite Net is then trained to predict the pneumatic performance of the fan. A non dominated sorting genetic algorithm is employed to solve the global optimization problem of the total pressure coefficient and efficiency. The simulation results show that the optimal blade load distribution along the radial direction becomes uniform, and the suction surface separation vortex and passage vortex are restrained. On the other hand, the tip leakage vortex is enhanced and moves toward the blade leading edge. According to the experimental results, the maximum efficiency increases by 5.44%, and the maximum total pressure coefficient increases by 2.47% after optimization.

23 November 2021 in Processes
Verified
Journal Article
Open access
PDF file
XYxiaopei yang
xiaopei yang
JWJun Wang
Jun Wang
BJBoyan Jiang
Boyan Jiang
ZLZhi’ang Li
Zhi’ang Li
qianhao xiaoqianhao xiao
qianhao xiao
Riblets with an appropriate size can effectively restrain turbulent boundary layer thickness and reduce viscous drag, but the effects of riblets strongly depend on the appearance of the fabric that is to be applied and its operating conditions. In this study, in order to improve the aerodynamic performance of a low-pressure fan by using riblet technology, sawtooth riblets on NACA4412 airfoil are examined at the low Reynolds number of 1 × 105, and the airfoil is operated at angles of attack (AOAs) ranging from approximately 0° to 12°. The numerical simulation is carried out by employing the SST k–ω turbulence model through the Ansys Fluent, and the effects of the riblets’ length and height on aerodynamic performance and flow characteristics of the airfoil are investigated. The results indicate that the amount of drag reduction varies greatly with riblet length and height and the AOA of airfoil flow. By contrast, the riblets are detrimental to the airfoil in some cases. The most effective riblet length is found to be a length of 0.8 chord, which increases the lift and reduces the drag under whole AOA conditions, and the maximum improvements in both are 17.46% and 15.04%, respectively. The most effective height for the riblet with the length of 0.5 chord is 0.6 mm. This also improves the aerodynamic performance and achieves a change rate of 12.67% and 14.8% in the lift and drag coefficients, respectively. In addition, the riblets facilitate a greater improvement in airfoil at larger AOAs. The flow fields demonstrate that the riblets with a drag reduction effect form “the antifriction-bearing” structure near the airfoil surface and effectively restrain the trailing separation vortex. The ultimate cause of the riblet drag reduction effect is the velocity gradient at the bottom of the boundary layers being increased by the riblets, which results in a decrease in boundary thickness and energy loss.

1 November 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
qianhao xiaoqianhao xiao
qianhao xiao
BJBoyan Jiang
Boyan Jiang
XYxiaopei yang
xiaopei yang
YDYanyan Ding
Yanyan Ding
JWJun Wang
Jun Wang
A large eddy simulation (LES) of a squirrel cage fan (SCF) provides a precise representation of turbulent flows with different degrees of complexity. This study comprehensively analyzes the coherent structures of turbulent flows in an SCF using an LES, proper orthogonal decomposition (POD), dynamic mode decomposition (DMD), and multi-resolution dynamic mode decomposition (mrDMD). An intelligent reduced-order model is established by integrating hierarchical deep learning and the sparse identification of nonlinear dynamics. The result shows that the evolution of the global DMD modes is attenuated due to the spatial distribution variations of localized high-frequency mrDMD modes, along with the fragmented and non-steady development of modal patterns. Unlike POD, DMD quantifies the quality of the impeller inlet environment and captures the antisymmetric low-dimensional flows associated with the shedding of rotating vortex structures. The interaction strength between stationary and dynamic rotating areas is accurately represented by attractors characterized by petal-like structures. The trajectory of the attractors faithfully maps the antisymmetric structural attributes, quasi-periodic behavior, and gradual attenuation characteristics exhibited by DMD modes. The number of petal-like systems and their temporal oscillations are in good agreement with the number of fan blades and their rotational cycles. This study provides new insight into fan engineering to advance flow control strategies and improve the understanding of the underlying flow mechanisms.

1 February 2023 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
qianhao xiaoqianhao xiao
qianhao xiao
JWJun Wang
Jun Wang
XYxiaopei yang
xiaopei yang
BJBoyan Jiang
Boyan Jiang
The chaotic state of microfluidic devices such as electroosmotic micromixers has received extensive attention. Its unsteady flow and multi-physics mask low-dimensional structure and potential attractors. Based on the dynamic mode decomposition and the sparse identification of nonlinear dynamics, this study aims to construct a manifold equation with the minimum degree of freedom, reveal the mixing mechanism of micromixers, and discover the evolution of chaotic states. The attenuation degree of freedom was introduced to force the modal coefficients to be pure oscillations. The six, four, and two-dimensional minimum reduced-order models (ROMs) were constructed under different mixing conditions. The nonlinear dynamics evolves on attractors resembling a six-petal structure based on the amplitude-phase method. The attractor periodicity and decay map the evolution of the periodic oscillation and limit cycle of the active modes and are related to the appearance of the low-energy dominant non-axisymmetric modes. These results emphasize the significance of ROM technology in revealing the low-dimensional structure and attractor of the electroosmotic micromixer.