Qiaoli Niu

Dr. Qiaoli Niu

Nanjing University of Posts & Telecommunications

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 January 2019 in Polymers
Verified
Journal Article
Open access
PDF file
MJMao Jiang
Mao Jiang
QNQiaoli Niu
Qiaoli Niu
XTXiao Tang
Xiao Tang
HZHeyi Zhang
Heyi Zhang
HXHaowen Xu
Haowen Xu
RXRuidong Xia
Ruidong Xia
The commonly used electron transport material (6,6)-phenyl-C61 butyric acid methyl ester (PCBM) for perovskite solar cells (PSC) with inverted planar structures suffers from properties such as poor film-forming. In this manuscript, we demonstrate a simple method to improve the film-forming properties of PCBM by doping PCBM with poly(9,9-dioctylfluorene-co-benzothiadiazole) (F8BT) as the electron transport layer (ETL), which effectively enhances the performance of CH3NH3PbI3 based solar cells. With 5 wt % F8BT in PCBM, the short circuit current (JSC) and fill factor (FF) of PSC both significantly increased from 17.21 ± 0.15 mA·cm−2 and 71.1 ± 0.07% to 19.28 ± 0.22 mA·cm−2 and 74.7 ± 0.21%, respectively, which led to a power conversion efficiency (PCE) improvement from 12.6 ± 0.24% to 15 ± 0.26%. The morphology investigation suggested that doping with F8BT facilitated the formation of a smooth and uniform ETL, which was favorable for the separation of electron-hole pairs, and therefore, an improved performance of PSC.

24 March 2017 in Molecules
Verified
Journal Article
Open access
PDF file
WZWenjin Zeng
Wenjin Zeng
XLXingming Liu
Xingming Liu
XGXiangru Guo
Xiangru Guo
QNQiaoli Niu
Qiaoli Niu
JYJianpeng Yi
Jianpeng Yi
YMYonggang Min
Yonggang Min
This review presents an overall discussion on the morphology analysis and optimization for perovskite (PVSK) solar cells. Surface morphology and energy alignment have been proven to play a dominant role in determining the device performance. The effect of the key parameters such as solution condition and preparation atmosphere on the crystallization of PVSK, the characterization of surface morphology and interface distribution in the perovskite layer is discussed in detail. Furthermore, the analysis of interface energy level alignment by using X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy is presented to reveals the correlation between morphology and charge generation and collection within the perovskite layer, and its influence on the device performance. The techniques including architecture modification, solvent annealing, etc. were reviewed as an efficient approach to improve the morphology of PVSK. It is expected that further progress will be achieved with more efforts devoted to the insight of the mechanism of surface engineering in the field of PVSK solar cells.

19 August 2019 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
QNQiaoli Niu
Qiaoli Niu
YDYunkai Deng
Yunkai Deng
DCDaiqi Cui
Daiqi Cui
HLHao Lv
Hao Lv
XDXiaomeng Duan
Xiaomeng Duan
YMYong Min
Yong Min

28 October 2019 in Scientific Reports
Verified
Journal Article
Open access
PDF file
HXHaowen Xu
Haowen Xu
HZHeyi Zhang
Heyi Zhang
YMYuhui Ma
Yuhui Ma
MJMao Jiang
Mao Jiang
YZYewei Zhang
Yewei Zhang
WHWei Huang
Wei Huang
The morphology of perovskite light-absorption layer plays an important role in the performance of perovskite solar cells (PSCs). In this work, BiFeO3 (BFO) nanostructures were used as additive for CH3NH3PbI3 (MAPbI3) via anti-solvent method. The addition of BFO nanostructures greatly enhanced the crystallinity, grain size and film uniformity of MAPbI3. As a result, the charge carrier mobility and electron diffusion length increased, leading to the increase of the short circuit current (JSC) of PSCs. This work provides a very simple but effective approach to improve the morphology of perovskite layer for efficient PSCs.

20 January 2022 in Polymers
Verified
Journal Article
Open access
PDF file
QNQiaoli Niu
Qiaoli Niu
LZLing Zhang
Ling Zhang
YXYao Xu
Yao Xu
CYChaochao Yuan
Chaochao Yuan
WQWeijie Qi
Weijie Qi
YMYonggang Min
Yonggang Min
Nonradiative recombination losses caused by defects in the perovskite layer seriously affects the efficiency and stability of perovskite solar cells (PSCs). Hence, defect passivation is an effective way to improve the performance of PSCs. In this work, trichloromelamine (TCM) was used as a defects passivator by adding it into the perovskite precursor solution. The experimental results show that the power conversion efficiency (PCE) of PSC increased from 18.87 to 20.15% after the addition of TCM. What’s more, the environmental stability of PSCs was also improved. The working mechanism of TCM was thoroughly investigated, which can be ascribed to the interaction between the –NH– group and uncoordinated lead ions in the perovskite. This work provides a promising strategy for achieving highly efficient and stable PSCs.

24 June 2023 in Molecules
Verified
Journal Article
Open access
PDF file
WHWei Hua
Wei Hua
QNQiaoli Niu
Qiaoli Niu
LZLing Zhang
Ling Zhang
BCBaoxiang Chai
Baoxiang Chai
JYJun Yang
Jun Yang
YMYonggang Min
Yonggang Min
Defects in perovskite films are one of the main factors that affect the efficiency and stability of halide perovskite solar cells (PSCs). Uncoordinated ions (such as Pb2+, I−) act as trap states, causing the undesirable non-radiative recombination of photogenerated carriers. The formation of Lewis acid–base adducts in perovskite directly involves the crystallization process, which can effectively passivate defects. In this work, 4-(trifluoromethyl)-1H-imidazole (THI) was introduced into the perovskite precursor solution as a passivation agent. THI is a typical amphoteric compound that exhibits a strong Lewis base property due to its lone pair electrons. It coordinates with Lewis acid Pb2+, leading to the reduction in defect density and increase in crystallinity of perovskite films. Finally, the power conversion efficiency (PCE) of PSC increased from 16.49% to 18.97% due to the simultaneous enhancement of open-circuit voltage (VOC), short circuit current density (JSC) and fill factor (FF). After 30 days of storage, the PCE of the 0.16 THI PSC was maintained at 61.9% of its initial value, which was 44.3% for the control device. The working mechanism of THI was investigated. This work provides an attractive alternative method to passivate the defects in perovskite.