Experimental investigations are made for the combined effects of aspect ratio (AR), slack (βS), and pitch angles on the aerodynamic characteristics of flexible flapping wings in hover. βS is introduced as a way to indirectly alter the flexibility of the wing. An optimum AR range of 3–5 based on the lift coefficient is observed depending on the flexibility. For a constant AR, the intensity of the leading-edge vortex (LEV) with corresponding circulatory-based lift mitigates as βS increases beyond 2.5°. The variation of βS affects the magnitude of the shed trailing-edge vortices (TEVs) but the vorticity core is maintained. We found the shed TEVs to be the key vortical feature of twistable flexible wings in comparison with the rigid (untwisted) cases. More intriguingly, the negative wing twist played a significant role in sustaining the circulatory lift at the outboard section for even high AR cases. The primary LEV trace is found to be an indicator for the effective spanwise limit of the LEV. Although an increase in AR reduces the effective spanwise limit, it is found that wing flexibility further decreases the radial distance. Again, the study reveals that lift enhancement in the rigid wing requires a wider effective downwash area induced by the outward movement of the LEV traces to merge with the tip vortex. Contrarily, the flexible wing requires an elongated downwash area induced by the wing twist to enhance the aerodynamic performance.
1 March 2023 in Journal of Mechanisms and Robotics
A lot of flapping-wing mechanisms have been proposed to mimic the flight characteristics of biological flyers. However, it is difficult to find studies that consider the unsteady aerodynamics in the design of the flapping-wing mechanisms. This paper presents a systematic approach to optimize the design parameters of a foldable flapping-wing mechanism (FFWM) with a proper aerodynamics model. For the kinematic model, the eight design parameters are defined to determine the reference configuration of the FFWM. The geometrical constraints of each design parameter are derived, and the kinematic analysis is conducted using the plane vector analysis method. The aerodynamic simulation using an unsteady vortex lattice method is performed to compute the aerodynamic loads induced by the flapping motion. An optimization problem is formulated to search for the optimal design parameters that maximize the average lift force considering the required power corresponding to the aerodynamic torques. The parameter optimization problem is solved for three different length ratios of the outer wing to the inner wing using a genetic algorithm. The optimization results show that increasing the outer wing length can cause a significant loss in the required power. The optimal design parameters found by the proposed approach allow the FFWM to generate maximum lift force with appropriate consideration of the required power.
Wing flexibility is unavoidable for flapping wing flyers to ensure a lightweight body and for higher payload allowances on board. It also effectively minimizes the inertia force from high-frequency wingbeat motion. However, related studies that attempt to clarify the essence of wing flexibility remain insufficient. Here, a parametric study of a flexible wing was conducted as part of the effort to build an aerodynamic model and analyze its aerodynamic performance. The quasi-steady modeling was adopted with experimentally determined translational forces. These forces were determined from 84 flexible wing cases while varying the angle of attack at the wing root αr and the flexibility parameter, slack angle θS, with 19 additional rigid wing cases. This study found αr for optimum lift generation to exceed 45° irrespective of θS. The coefficient curves were well-fitted with a cubed-sine function. The model was rigorously validated with various wing kinematics, giving a good estimation of the experimental results. The estimated error was less than 5%, 6%, and 8% for the lift, drag, and moment, respectively, considering fast to moderate wing kinematics. The study was extended to analyze the pure aerodynamic performance of the flexible wing. The most suitable wing for a flapping-wing micro-aerial vehicle wing design with a simple vein structure was found to be the 5° slack-angled wing. The inference from this study further shows that a small amount of deformation is needed to increase the lift, as observed in natural flyers. Thus, wing deformation could allow living flyers to undertake less pitching motion in order to reduce the mechanical power and increase the efficiency of their wings.
20 December 2018 in Journal of Intelligent Material Systems and Structures
A new actuation mechanism using the twisted string concept to trigger the snap-through of a bistable buckled beam to produce an effective on/off bistable actuator is proposed. The twisted string concept combined with a pin utilizes actuation moment to actuate a bistable beam. The required actuation loads are analytically formulated using the Euler–Bernoulli beam model and solved with the proposed solution algorithm. The actuation mechanism is fabricated to meet the 24.3 N mm actuation requirements. A prototype of the actuator was built, and its performance was evaluated. In a unidirectional actuation, an actuator response time of 104 ms was achieved. The overall response time of the actuator is affected by the length of the string. The twisted string mechanism was also placed in an antagonistic configuration to enable bidirectional actuation. The shape of the input voltage signal also affected the bidirectional performance of the actuator. The actuator produced an actuation bandwidth of 2 and 5 Hz with sine and square input voltages, respectively, while generating 10 mm output displacement.