In this paper, a Microgrid (MG) test model based on the 14-busbar IEEE distribution system is proposed. This model can constitute an important research tool for the analysis of electrical grids in its transition to Smart Grids (SG). The benchmark is used as a base case for power flow analysis and quality variables related with SG and holds distributed resources. The proposed MG consists of DC and AC buses with different types of loads and distributed generation at two voltage levels. A complete model of this MG has been simulated using the MATLAB/Simulink environmental simulation platform. The proposed electrical system will provide a base case for other studies such as: reactive power compensation, stability and inertia analysis, reliability, demand response studies, hierarchical control, fault tolerant control, optimization and energy storage strategies.
The UPFC is one of the most important flexible AC transmission systems (FACTS), since it can provide various types of compensation. The UPFC is implemented by using two voltage source converters which are connected through a common DC link capacitor. Each converter is coupled to the power system with a transformer. The paper deals with the mathematical modeling and analysis of a sinusoidal pulse width modulation (SPWM) based UPFC. A model-free approach for the selection of the controller may also be an acceptable solution. The design and simulation of a matrix PI controller and a fuzzy logic controller have been carried out. From the simulation results, it is demonstrated that it can control real and reactive power. Simulations using the electromagnetic transients program (ATP/EMTP) and MATLAB/Simulink program are shown. The dynamic performance in terms of accuracy, speed, stability, robustness and simplicity are compared
This paper proposes a hybrid quantum–classical framework for distribution network reconfiguration (DNR) under high distributed generation (DG) penetration, integrating nonlinear AC power-flow validation with the Quantum Approximate Optimization Algorithm (QAOA). Unlike prior quantum-assisted studies that rely on simplified DC or surrogate models, the proposed approach embeds AC-feasible loss evaluation directly within the combinatorial optimization loop. The methodology first evaluates all admissible switching configurations of the IEEE 33-bus system under DG integration using full AC power flow. The resulting loss landscape is compressed into a Quadratic Unconstrained Binary Optimization (QUBO) representation and mapped to an Ising Hamiltonian, enabling variational optimization via QAOA. The dominant configuration suggested by the quantum layer is subsequently validated through AC feasibility analysis. Simulation results show that the coordinated DG + QAOA strategy reduces active power losses from 282.938 kW (baseline) to 95.773 kW, corresponding to a 66.15% reduction relative to the original topology and an additional 20.62% improvement beyond DG-only operation. The minimum bus voltage increases from 0.8828 p.u. to 0.9531 p.u., satisfying IEEE 1547 limits, while requiring only two switching operations. These results demonstrate that embedding AC-consistent validation within a hybrid QAOA framework enhances physical realism, scalability, and solution quality for combinatorial optimization in active distribution networks.
Passive single-phase to three-phase conversion represents an attractive alternative for low-power applications, particularly in isolated systems and rural electrification scenarios where simplicity, robustness, and low cost are essential. However, these passive topologies inherently produce voltage unbalance whose magnitude strongly depends on load characteristics. This work analyzes a passive single-phase to three-phase converter based on reactive elements and a transformer, focusing on the limits of voltage unbalance mitigation through discrete transformer tap optimization. The study is conducted under steady-state sinusoidal conditions using phasor modeling and symmetrical component analysis. The voltage unbalance factor (VUF) is adopted as the primary optimization metric, while the current unbalance factor (IUF), neutral current, and converter losses are used as complementary performance indicators. Results indicate that transformer tap optimization can reduce voltage unbalance for specific load conditions, although low residual unbalance is achieved only near the nominal operating point. Higher residual unbalance is observed as the load becomes more inductive within the investigated power-factor range. The findings indicate that passive single-phase to three-phase conversion can be technically viable for low-power applications with relatively stable load conditions. However, applications requiring high power quality or dynamic regulation may benefit from active converter solutions based on power electronics.
En este capítulo se presentan los conceptos relacionados con los números y las funciones. Se inicia con la clasificación de los distintos conjuntos numéricos, desde los naturales hasta los complejos. Luego, se introducen las inecuaciones, abordando sus propiedades, representación gráfica, técnicas de resolución y casos que involucran valores absolutos. Posteriormente, se estudian las relaciones y funciones numéricas, con énfasis en la clasificación según su comportamiento (inyectivas, sobreyectivas, biyectivas) y en la definición de su inversa. Finalmente, se analizan las funciones en el plano cartesiano y se propone una serie de ejercicios para reforzar los contenidos tratados. Los números están presentes en todas las áreas del conocimiento y constituyen la base de cualquier concepto matemático, independientemente del nivel académico. Para los ingenieros, no solo es fundamental conocerlos, sino también comprenderlos a profundidad, identificando sus diferentes clasificaciones y propiedades. Por ello, dedicamos este primer apartado a explorar la clasificación de los números, permitiendo así una base sólida para su aplicación en contextos técnicos y científicos.
En este capítulo se presentan diversas aplicaciones de las funciones reales en diferentes ramas de la ingeniería. Se exploran ejemplos concretos en los campos de la ingeniería civil, agropecuaria, automotriz, mecánica, eléctrica y electrónica, con el objetivo de mostrar cómo los conceptos matemáticos adquiridos pueden utilizarse para modelar, analizar y resolver problemas reales en contextos técnicos. Cada sección aborda situaciones específicas donde las funciones permiten representar fenómenos físicos, establecer relaciones entre variables y tomar decisiones basadas en modelos matemáticos. Al final del capítulo, se incluye una sección de desafíos para el aprendizaje, que invita a reflexionar sobre los contenidos tratados y a poner en práctica los conocimientos adquiridos mediante problemas contextualizados.