Rong Situ

Dr. Rong Situ

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 July 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
MMMobin Majeed
Mobin Majeed
Rong SituRong Situ
Rong Situ
Triply periodic minimal surfaces (TPMS), structures fabricated from Inconel 718 (In718) via selective laser melting (SLM), found their potential applications in the aviation and energy industries owing to their excellent anticorrosive properties and thermal stability. However, the SLM process induces micro-segregation, anisotropic mechanical properties, and detrimental phases (Laves, $$\delta$$ δ ) which degrade its mechanical properties. Although heat treatment has shown promising results for bulk In718 material, its impact on TPMS structures has received very limited attention. This research investigates the impact of standard heat treatments, including stress relieving (SR), homogenization plus ageing (HSA), and direct ageing (DA), on the properties of diamond and gyroid TPMS structures. The quasistatic compression tests were conducted in an Instron machine, and material characterisation was conducted in Scanning Electron Microscopy (SEM) and X-ray diffraction (XRD). HSA treatment has led to maximum improvement; the compressive strength and yield strength of diamond TPMS were improved by 58.55% and 93.5% respectively, due to the precipitation of strengthening phases ( $$\gamma^{\prime }$$ γ ′ and $$\gamma^{\prime \prime }$$ γ ″ ) and dissolution of detrimental phases. HSA and DA treatments led to stretch dominated deformation and higher energy absorption capacity. Conversely SR treatment has shown bending dominated deformation behaviour and degraded mechanical properties in contrast to the previous studies on tensile samples.

27 February 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
MMMobin Majeed
Mobin Majeed
Rong SituRong Situ
Rong Situ
ZJZia Javanbakht
Zia Javanbakht
This study aims to investigate the effect of heat treatment on the microstructure and mechanical properties of triply periodic minimal surface (TPMS) structures manufactured by selective laser melting (SLM) from Inconel® alloy 718 (In718). Although many aspects of SLM-In718 have been studied, its as-built (AB) and heat treated (HT) performance under compression has not been thoroughly investigated. To this end, sheet-based diamond, gyroid, and primitive morphologies along with bulk specimens were manufactured and tested under AB and HT conditions. Standard solution ageing (solution treatment + two-step ageing) was carried out to improve some of the inherent deficiencies of SLM-In718 such as the development of brittle Laves and $$\delta$$ δ phases. It was found that the overall mechanical performance of the HT TPMS specimens were improved in terms of stiffness, strength, and energy absorption among others. Furthermore, the geometry of the TPMS specimens dictated the extent of enhancement such that the diamond geometry outperformed the others in many aspects. In contrast, the primitive structure demonstrated the most stable plateau stage in both AB and HT conditions. Microstructural analysis revealed occasional precipitation of second-phases carbide particles at grain boundaries. Moreover, niobium was made available by dissolution of Laves phases during solution treatment which was later used in precipitation of strengthening $$\gamma ^{\prime}$$ γ ′ and $$\gamma ^{\prime\prime}$$ γ ″ phases during ageing. Finally, a new scheme for analysing the energy absorption was devised which could provide a new perspective towards studying energy efficiency of porous structures. Accordingly, it was found that heat treatment improves the mechanical properties contributing the first two stages of energy absorption (initial and plateau) while limiting the fraction of the final stage. In conclusion, it was demonstrated that although heat treatment could address issues like residual stresses and microstructural shortcomings of SLM-In718, the extent of this rectification is further controlled by cell topology of the TPMS structure.

1 November 2018 in Energies
Verified
Journal Article
Open access
PDF file
AAAhmed Adeeb Abdulwahid
Ahmed Adeeb Abdulwahid
Rong SituRong Situ
Rong Situ
RBRichard J. Brown
Richard J. Brown
Diesel engines release a range of harmful components into the environment in the form of gases, liquids, and particulate matter (PM). These components have a direct and indirect impact on human health and climate change. Wet scrubbers are used to clean diesel exhaust emissions, by bubbling them through a liquid (usually water) to reduce their temperature and remove some soluble components and particles. Then, these emissions pass through a filter to remove further diesel particulate matter. The PM-capturing mechanism, heat transfer mechanism, and fluid mechanism of a wet scrubber are reviewed. Several parameters have a major influence on wet scrubber performance, such as inlet gas velocity. Modeling of a wet scrubber can be conducted through thermodynamics analysis, heat transfer analysis, and computational simulation. These investigations may lead to optimizing wet scrubber performance, and then to reducing both humidity and temperature at the scrubber exit. This humidity reduction increases filter life and reduces maintenance costs.

1 April 2013 in Marine Pollution Bulletin
Verified
Journal Article
Closed access
Rong SituRong Situ
Rong Situ
RBRichard J. Brown
Richard J. Brown

4 September 2010 in Environmental Fluid Mechanics
Verified
Journal Article
Closed access
PDF file
Rong SituRong Situ
Rong Situ
RBRichard J. Brown
Richard J. Brown
ALAnthony Loberto
Anthony Loberto

11 August 2026 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
MMMobin Majeed
Mobin Majeed
JZJianjun Zhang
Jianjun Zhang
GLGuoxing Lu
Guoxing Lu
DGDongye Gao
Dongye Gao
GYGuolei Yang
Guolei Yang
Rong SituRong Situ
Rong Situ
Triply periodic minimal surfaces (TPMS), specially made from Inconel 718 (In718), are suitable for aerospace, automotive, and energy sector components due to their superior physical properties. Currently, TPMS structures have been investigated for their mechanical performance under quasi-static compression; however, limited attention is paid to their performance in dynamic loading. In this study the TPMS structures were additively manufactured with suitable processing parameters. Later a multiple-step heat treatment was applied to these TPMSs. Quasistatic and dynamic impact tests at different loading velocities were conducted on those samples using a universal testing machine. The microstructure of the samples was investigated in scanning electron microscopy (SEM), and a comparison was made between the as-built and heat-treated samples. The impact of heat treatment and different phases on their mechanical properties was discussed. It was found that heat treatment has made substantial improvements in microstructure: dissolved detrimental phases and precipitated strengthening phases. The results demonstrated significantly higher strength of the TPMS structures under dynamic loading conditions, with the elastic modulus of the diamond TPMS increased by as much as 541%, while other properties were at least doubled compared to quasi-static mechanical properties. In addition, the energy absorption properties were almost doubled under impact loading as compared to the quasistatic loading condition and further improved by the heat treatment process.