Per- and polyfluoroalkyl substances (PFAS) are persistent organic pollutants of growing environmental and human health concern, widely detected across various environmental compartments. Effective remediation strategies are essential to mitigate their widespread impacts. This study compared the performance of two types of commercially available sorbent materials, granular activated carbon (GAC, Filtrasorb-400) and organoclays (OC-200, and modified organoclays Fluoro-sorb-100 and Fluoro-sorb-200) for the removal of three representative PFAS compounds: perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), and perfluorooctane sulfonic acid (PFOS) from water. Both organoclays and modified organoclays outperformed GAC, likely due to electrostatic interactions between the anionic PFAS compounds and the cationic functional groups of the modified organoclays. A pseudo-second-order kinetic model best described the rapid sorption kinetics of PFOA, PFNA, and PFOS. For PFOA, OC-200 demonstrated the highest adsorption capacities (qmax = 47.17 µg/g). For PFNA and PFOS, Fluoro-sorb-100 was the most effective sorbent, with qmax values at 99.01 µg/g and 65.79 µg/g, respectively. Desorption studies indicated that the sorption of the three PFAS compounds on these commercially available sorbents was largely irreversible. This study highlights the effectiveness and sorption capacities of different types of commercial sorbents for PFAS removal and offers valuable insights into the selection of reactive media for PFAS removal from water under environmentally relevant conditions.
Per- and polyfluoroalkyl substances (PFAS) are fluorinated and refractory pollutants that are ubiquitous in industrial wastewater. Photocatalytic destruction of such pollutants with catalysts such as TiO2 and ZnO is an attractive avenue for removal of PFAS, but refined forms of such photocatalysts are expensive. This study, for the first time, utilized milled unrefined raw mineral ilmenite, coupled to UV-C irradiation to achieve mineralization of the two model PFAS compounds perfluorooctanoic acid (PFOA) and perfluoro octane sulfonic acid (PFOS). Results obtained using a bench-scale photocatalytic reactor system demonstrated rapid removal kinetics of PFAS compounds (>90% removal in less than 10 h) in environmentally-relevant concentrations (200–1000 ppb). Raw ilmenite was reused over three consecutive degradation cycles of PFAS, retaining >80% removal efficiency. Analysis of degradation products indicated defluorination and the presence of shorter-chain PFAS intermediates in the initial samples. End samples indicated the disappearance of short-chain PFAS intermediates and further accumulation of fluoride ions, suggesting that original PFAS compounds underwent mineralization due to an oxygen-radical-based photocatalytic destruction mechanism induced by TiO2 present in ilmenite and UV irradiation. The outcome of this study implies that raw ilmenite coupled to UV-C is suitable for cost-effective reactor operation and efficient photocatalytic destruction of PFAS compounds.
Over the past several decades, the value of drinking water treatment residuals (WTRs), a byproduct of the coagulation process during water purification, has been recognized in various environmental applications, including sustainable remediation of phosphorus (P)-enriched soils. Aluminum-based WTRs (Al-WTRs) are suitable adsorbent materials for P, which can be obtained and processed inexpensively. However, given their heterogeneous nature, it is essential to identify an easily analyzable chemical property that can predict the capability of Al-WTRs to bind P before soil amendment. To address this issue, thirteen Al-WTRs were collected from various geographical locations around the United States. The non-hazardous nature of the Al-WTRs was ascertained first. Then, their P adsorption capacities were determined, and the chemical properties likely to influence their adsorption capacities were examined. Statistical models were built to identify a single property to best predict the P adsorption capacity of the Al-WTRs. Results show that all investigated Al-WTRs are safe for environmental applications, and oxalate-extractable aluminum is a significant indicator of the P adsorption capacity of Al-WTRs (p-value = 0.0002, R2 = 0.7). This study is the first to report a simple chemical test that can be easily applied to predict the efficacy of Al-WTRs in binding P before their broadscale land application.
Despite the prevalence and toxicity of heavy metals in the environment, arsenic and cobalt are of particular concern due to their high mobility and bioaccumulation potential, particularly in contaminated groundwater. Herein, we studied the adsorption behavior of commercially available sorbents, including Fluorosorb-100 (FS-100), Fluorosorb-200 (FS-200), and Filtrasorb-400 (F-400), for the removal of arsenite (As(III)) and cobalt (Co(II)), aiming at the selection of filter media in terms of future groundwater remediation. Kinetic analysis revealed that As(III) adsorption followed a pseudo-second-order model, while Co(II) showed mixed first- and second-order behavior, reflecting sorbent-dependent mechanisms. Equilibrium isotherm modeling revealed strong correlations with both Langmuir and Freundlich models, confirming heterogeneous adsorption sites and multilayer interactions. FS-100 demonstrated the highest affinity for As(III) (qₘ = 0.46 mg/g) and F-400 exhibited the greatest adsorption capacity for Co(II) (qₘ = 1.00 mg/g), while FS-200 consistently showed relatively weaker adsorption for both metals. Desorption studies indicated predominantly irreversible binding, with minimal release of As(III) from F-400 and Co(II) from FS-200 and F-400, even at high concentrations. Overall, these findings highlight that commercially available sorbents can effectively capture arsenite and cobalt, offering cost-effective and scalable options for heavy-metal removal in groundwater remediation systems under realistic environmental conditions.
The Los Angeles (LA) wildland-urban interface (WUI) fires of January 2025, are among the most destructive natural disasters in U.S. history, generating complex emission profiles that remain insufficiently characterized. An intensive field sampling campaign was conducted during the active burn period to collect and characterize the complex physicochemical properties of size-segregated particulate matter (WUIF-PM), vapor-phase compounds (WUIF-VOC), and ash (WUIF ash). While regulatory air quality indices remained within moderate categories during the sampling period, chemical analyses revealed substantial enrichment of hazardous species relative to urban background and biomass-only wildfire conditions. Oxygenated and highly toxic polycyclic aromatic hydrocarbons (OPAHs) were found in ultrafine WUIF-PM0.1, (size < 100 nm) and the fractional concentration (µg/g) of US EPA 16 priority polycyclic aromatic hydrocarbons (PAHs) in WUIF-PM2.5 exceeded recent levels for LA background, and biomass-only wildfires by an order of magnitude due to the excessive burn of human-made structures. Non-crustal metals were predominantly concentrated in WUIF-PM0.1 and consistently enriched relative to both LA background (up to ∼30 ×) and biomass-only wildfire aerosols (10-1000 ×). Benzene, toluene, ethylbenzene, and xylene (BTEX) concentrations in WUIF-VOC air samples were 4.8-13-fold higher than background levels. More alarmingly, WUIF ash samples contained PAHs, metals, and per- and polyfluoroalkyl substances (PFAS) consistent with mixed combustion of structural materials and vegetation raising concerns for post-fire environmental health risks. These findings indicate that PM₂.₅ mass and criteria air pollutants alone may underestimate the toxicological burden of WUI smoke, and expanded physicochemical monitoring and characterization is needed to advance exposure assessment and health risk evaluation during complex WUI fire events.