Rudolf Seracino

Prof. Rudolf Seracino

Civil, Construction, and Environmental Engineering, North Carolina State University, Raleigh, North Carolina, USA
orcid
Paul and Dora Zia Distinguished Professor

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2011 in Engineering Structures
Verified
Journal Article
Closed access
SSScott T. Smith
Scott T. Smith
SHShenghua Hu
Shenghua Hu
SKSeo Jin Kim
Seo Jin Kim
Rudolf SeracinoRudolf Seracino
Rudolf Seracino

1 August 2007 in Journal of Composites for Construction
Verified
Journal Article
Closed access
Rudolf SeracinoRudolf Seracino
Rudolf Seracino
NJNicola M. Jones
Nicola M. Jones
MAM. S. Ali
M. S. Ali
MPMark W. Page
Mark W. Page
DODeric J. Oehlers
Deric J. Oehlers
The retrofitting technique of near-surface mounting (NSM) fiber-reinforced polymer (FRP) bars/strips is receiving more attention recently due to a number of advantages over the externally bonded technique. However, there is insufficient data available in the existing literature to quantify the intermediate crack (IC) debonding mechanism of reinforced concrete members retrofitted with longitudinal NSM strips. As it is recognized that simple push–pull specimens simulate the IC debonding mechanism observed in retrofitted flexural members, this paper presents the results of a series of 36 push–pull tests using NSM strips to quantify the bond strength of such FRP-to-concrete joints. It is proposed that the confinement effect of the concrete surrounding the interface debonding crack improves the shear stress transfer mechanism resulting in higher debonding plate strains compared with externally bonded plates. A nonlinear statistical analysis of the experimental data was undertaken to develop a model to predict ...

1 August 2013 in Journal of Composites for Construction
Verified
Journal Article
Closed access
JSJiawei Shi
Jiawei Shi
HZHong Zhu
Hong Zhu
ZWZhishen Wu
Zhishen Wu
Rudolf SeracinoRudolf Seracino
Rudolf Seracino
GWG. Wu
G. Wu
This paper presents an experimental investigation on the bond behavior between basalt fiber–reinforced polymer (BFRP) sheet and concrete substrate under the coupled effects of freeze-thaw cycling and sustained load. Test variables were freeze-thaw cycles, level of sustained load, and adhesive type. Double-lap shear specimens were used in the tests, and a specially designed reaction-loading system was used to apply the sustained load during freeze-thaw cycles. Specimens with or without sustained load were exposed to up to 300 freeze-thaw cycles. A modified epoxy resin, made by adding a toughening agent to the original epoxy resin, was used in the test to study the effect of adhesive type on the durability of the BFRP–concrete interface. Coupon tests were also conducted to determine the freeze-thaw resistance of the constituent materials of the BFRP–concrete interface. After exposure, double-lap shear tests were carried out to investigate the residual bond capacity of the BFRP–concrete interface. Digital image correlation measurement was applied to capture the full-field deformation of the FRP sheet and the concrete block during the double-lap shear tests. A nonlinear bond-slip relationship of the BFRP–concrete interface was determined based on the analysis of displacement data. Test results show that (1) the bond capacity of the BFRP–concrete interface decreases with increasing freeze-thaw cycles, (2) the failure mode changes from debonding in the concrete layer to debonding in the adhesive layer, (3) extra degradation of the bond-slip relationship could be caused by the coupled effects, and (4) the durability improvement of the adhesive may result in a better durability of the BFRP–concrete bond capacity in a freeze-thaw environment. Finally, the coupled effects and evaluation of freeze-thaw procedures on the bond degradation of FRP–concrete interface are discussed.

1 January 2014 in Construction and Building Materials
Verified
Journal Article
Closed access
AEAdel Elsaid
Adel Elsaid
Rudolf SeracinoRudolf Seracino
Rudolf Seracino

1 March 2016 in Construction and Building Materials
Verified
Journal Article
Closed access
KMKuihua Mei
Kuihua Mei
Rudolf SeracinoRudolf Seracino
Rudolf Seracino
ZLZhitao Lv
Zhitao Lv

1 December 2008 in Journal of Composites for Construction
Verified
Journal Article
Closed access
DODeric John Oehlers
Deric John Oehlers
MHMatthew Haskett
Matthew Haskett
CWChengqing Wu
Chengqing Wu
Rudolf SeracinoRudolf Seracino
Rudolf Seracino
The use of near surface mounted (NSM) fiber reinforced polymer (FRP) strips for strengthening reinforced concrete structures shows great promise as the strains at intermediate crack (IC) debonding are generally much greater than for externally bonded FRP strips. In this research, the NSM technique is taken a step further by embedding the NSM strip, i.e., is by providing cover to the strip. It is shown that embedment can increase the IC debonding resistance by up to three times. Importantly, embedment allows: substantially larger strains at IC debonding and, hence, greater ductility; the use of larger cross sections of FRP plate; and, through providing cover to the NSM, may be the first step in enhancing the fire resistance. In this paper, 20 new pull tests are described from which mathematical expressions are developed for the effect of embedment on both the IC debonding resistance and its associated local bond stress–slip (τ–δ) relationship.