Saeedeh Barzegar-Parizi

Dr. Saeedeh Barzegar-Parizi

Sirjan University of Technology
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 July 2015 in IEEE Journal of Quantum Electronics
Verified
Journal Article
Closed access
Saeedeh Barzegar-PariziSaeedeh Barzegar-Parizi
Saeedeh Barzegar-Parizi
BRBehzad Rejaei
Behzad Rejaei
AKAmin Khavasi
Amin Khavasi
In this paper, an analytical circuit model is proposed for 2-D arrays of graphene disks. First, we derive an analytical expression for the surface current density on a single graphene disk in the subwavelength regime, induced by a normally incident plane wave. The solution is then extended to 2-D arrays of graphene disks using perturbation theory. Finally, by applying appropriate boundary conditions, an R-L-C equivalent circuit of the structure is obtained. It is shown that both a single graphene disk and periodic array of graphene disks have dual capacitive-inductive nature. The results of the proposed model are in excellent agreement with those obtained by full-wave simulations.

9 March 2024 in Scientific Reports
Verified
Journal Article
Open access
PDF file
Saeedeh Barzegar-PariziSaeedeh Barzegar-Parizi
Saeedeh Barzegar-Parizi
AEAmir Ebrahimi
Amir Ebrahimi
KGKamran Ghorbani
Kamran Ghorbani
This article presents the design of a 2-bit dual-band switchable terahertz absorber using a stacked combination of graphene and vanadium dioxide (VO2) metamaterials. For the first time, the proposed absorber design offers four switchable states by controlling the conductivity of graphene and VO2 metamaterial layers. The lower absorption band is produced by the graphene metamaterial, whereas the upper band is implemented by the VO2 metamaterial pattern. The structure shows two absorption bands (State 11) at 0.745–0.775 THz and 2.3–5.63 THz, when the Fermi graphene level of graphene is 0.2 eV and the VO2 is in the metallic phase. The lower absorption band is turned off, while keeping the upper band (State 01), when the graphene Fermi level is 0 eV and the VO2 layer is in the metallic phase. The upper absorption band is turned off, while preserving the lower absorption band (State 10) by switching the VO2 into the insulator phase and keeping the graphene Fermi level at 0.2 eV. Finally, both of the absorption bands are turned off by setting the graphene Fermi level to 0 eV and switching the VO2 into the insulating phase. Equivalent circuit modelling analysis and full-wave electromagnetic simulations are used to explain the operation principle of the proposed absorber. Very good agreement is obtained between the theoretical analysis and the simulations confirming the presented design principle for the 2-bit switchable absorber.

27 February 2019 in IEEE Journal of Quantum Electronics
Verified
Journal Article
Closed access
Saeedeh Barzegar-PariziSaeedeh Barzegar-Parizi
Saeedeh Barzegar-Parizi
AKAmin Khavasi
Amin Khavasi
This article presents a novel approach for designing dual-band absorbers based on graphene and metallic metasurfaces for terahertz and mid-infrared regimes, respectively. The absorbers are composed of a two-dimensional (2D) array of square patches deposited on a dielectric film terminated by a metal plate. Using an analytical circuit model, we obtain closed-form relations for different parameters of the structure to achieve the dual-band absorber. Two absorption bands with obtained absorptivity of 98% at 0.53 and 1.53 THz for the graphene-based structure and 7 and 25 THz for the metallicbased case are achieved. We demonstrate that the graphenebased absorber remains as the dual-band for a wide range of the Fermi level. Furthermore, the recommended dual-band absorbers are insensitive in terms of polarization and remain within various incident angles. The most important advantage of this device is its simplicity compared to previously reported structures.

28 July 2020 in Journal of the Optical Society of America B
Verified
Journal Article
Closed access
PDF file
Saeedeh Barzegar-PariziSaeedeh Barzegar-Parizi
Saeedeh Barzegar-Parizi
AEAmir Ebrahimi
Amir Ebrahimi
This article presents multi-band plasmonic absorbers based on a graphene array at terahertz frequencies. The absorbers are made of a very simple structure including a graphene disk array printed on the top surface of a dielectric spacer backed by a metallic ground plane. Multi-band performance is achieved with more than 90% absorption in the 1–8 THz frequency range by exciting surface plasmon polaritons of graphene. It is shown that the resonance frequencies of the proposed absorber can be tuned by varying the chemical potential between 0.8–1 eV for a triple-band absorber and 0.7–0.9 eV for a quad-band one, while keeping more than 80% absorption. The results obtained by means of full-wave simulation are verified with the results obtained by the analytical circuit model. The proposed absorbers are polarization-insensitive and provide stable absorption performance for both of the TE and TM polarizations. As an application, we designed a refractive index sensor based on the triple-band absorber. The results verify that the absorption bands are sensitive to the variations of the refractive index of the coating layer.

1 December 2022 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
Saeedeh Barzegar-PariziSaeedeh Barzegar-Parizi
Saeedeh Barzegar-Parizi
ZVZohreh Vafapour
Zohreh Vafapour
Temperature-sensitive materials are known as phase change materials (PCMs) which has transition between two different states. Dynamically tunable devices can be designed utilizing these materials. Vanadium dioxide (VO $_{2})$ considered as a PCM material which transits from the insulator state to the metal one by increasing the temperature. VO $_{2}$ has recently been utilized to design tunable absorbers. In this article, we presented a dual-band absorber structure design which consist of double arrays of VO $_{2}$ ring-based placed on top of a dielectric buffer/spacer terminated with a conducting layer acting as a back reflector. Each ring acts as a resonator producing a surface plasmon resonance (SPR). Having a proper unit cell design with an appropriate dimension, a dual-band absorber with an absorption amplitude above 95% (on state) can be achieved at terahertz (THz) frequency range in the metallic state; whereas the absorption value is 0.6% (off state) in the insulator state of VO $_{2}$ . Therefore, the proposed structure design has the possibility to switch between these two on/off states by changing the material’s temperature. The interference theory and the equivalent circuit model are investigated to verify the achieved result using high-frequency structure simulator (HFSS) software which works based on finite element method (FEM). This structure has the potential optoelectronic applications such as refractive index (RI) optical sensing and biomedical detection, photonics detectors, and optical storage applications.