Saja M. Nabat Al-Ajrash

Dr. Saja M. Nabat Al-Ajrash

University of Dayton, USA
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 January 2014 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
AAAhmed Al-Roubaiy
Ahmed Al-Roubaiy
SASaja M. Nabat Al-Ajrash
Saja M. Nabat Al-Ajrash
Andre D.L. BatakoAndre D.L. Batako
Andre D.L. Batako

24 March 2021 in Polymers
Verified
Journal Article
Open access
PDF file
SDSuchitha Devadas
Suchitha Devadas
SASaja M. Nabat Al-Ajrash
Saja M. Nabat Al-Ajrash
DKDonald A. Klosterman
Donald A. Klosterman
KCKenya M. Crosson
Kenya M. Crosson
GCGarry S. Crosson
Garry S. Crosson
Erick S Vasquez-GuardadoErick S Vasquez-Guardado
Erick S Vasquez-Guardado
Lignin macromolecules are potential precursor materials for producing electrospun nanofibers for composite applications. However, little is known about the effect of lignin type and blend ratios with synthetic polymers. This study analyzed blends of poly(acrylonitrile-co-methyl acrylate) (PAN-MA) with two types of commercially available lignin, low sulfonate (LSL) and alkali, kraft lignin (AL), in DMF solvent. The electrospinning and polymer blend solution conditions were optimized to produce thermally stable, smooth lignin-based nanofibers with total polymer content of up to 20 wt % in solution and a 50/50 blend weight ratio. Microscopy studies revealed that AL blends possess good solubility, miscibility, and dispersibility compared to LSL blends. Despite the lignin content or type, rheological studies demonstrated that PAN-MA concentration in solution dictated the blend’s viscosity. Smooth electrospun nanofibers were fabricated using AL depending upon the total polymer content and blend ratio. AL’s addition to PAN-MA did not affect the glass transition or degradation temperatures of the nanofibers compared to neat PAN-MA. We confirmed the presence of each lignin type within PAN-MA nanofibers through infrared spectroscopy. PAN-MA/AL nanofibers possessed similar morphological and thermal properties as PAN-MA; thus, these lignin-based nanofibers can replace PAN in future applications, including production of carbon fibers and supercapacitors.

15 January 2021 in Materials Advances
Verified
Journal Article
Open access
PDF file
SASaja M. Nabat Al-Ajrash
Saja M. Nabat Al-Ajrash
CBCharles Browning
Charles Browning
RERose Eckerle
Rose Eckerle
LCLi Cao
Li Cao
Investigation of three preceramic polymer formulations for potential use in additive manufacturing technologies.

7 November 2017 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
SASaja M. Nabat Al-Ajrash
Saja M. Nabat Al-Ajrash
KLKhalid Lafdi
Khalid Lafdi
YLYufei Liu
Yufei Liu
Philippe Le CoustumerPhilippe Le Coustumer
Philippe Le Coustumer

4 May 2021 in Nano Select
Verified
Journal Article
Open access
PDF file
SASaja M. Nabat Al-Ajrash
Saja M. Nabat Al-Ajrash
CBCharles Browning
Charles Browning
RERose Eckerle
Rose Eckerle
LCLi Cao
Li Cao
A novel route to fabricating hybrid ceramic matrix composites has been developed. The fabrication is based on the unique combination of additive manufacturing (AM), a preceramic polymer, and a chopped carbon fiber precursor. After introducing the photoinitiator to the preceramic polymer formulation, a photosensitive resin was introduced. The resulting resin was loaded with distinct weight percentages of stabilized polyacrylonitrile nanofiber—the carbon fiber precursor. These formulations were 3D printed, cured, and converted to ceramic phases using a pyrolysis cycle. The end objective of the pyrolysis cycle is the conversion of the polycarbosilane resin into a silicon carbide matrix and the transformation of the PAN polymer into reinforcing carbon nanofibers within one cycle. The results of this work showed that ceramic matrix composite components can be successfully fabricated using a suitable combination of 3D printing, resin formulation, and processing cycle. The pyrolyzed ceramic hybrid composite was fully dense with nearly linear shrinkage and a shiny, smooth surface. Approximately 60% retained weight after pyrolysis to 1350°C was confirmed by thermogravimetric analysis. In terms of crystallography, the ceramic matrix composite displayed three coexisting phases including silicon carbide, silicon oxycarbide, and turbostratic carbon. The results showed this combination of material and processes has a high potential for fabricating hybrid composites with high‐temperature performance and improved mechanical properties combined with complex geometries.

25 May 2018 in Langmuir
Verified
Journal Article
Closed access
SASaja M. Nabat Al-Ajrash
Saja M. Nabat Al-Ajrash
KLKhalid Lafdi
Khalid Lafdi
Erick S Vasquez-GuardadoErick S Vasquez-Guardado
Erick S Vasquez-Guardado
FCFrancisco Chinesta
Francisco Chinesta
PCPhilippe Le Coustumer
Philippe Le Coustumer