Energy addition using a hot surface ignition device is required for reliable ignition of aircraft compression ignition engines running on fuel variations and at altitude conditions. Thus, durability of the hot surface ignition device is crucial for application in these engines. Thermomechanical stress is one of the key parameters that determine durability, which requires an accurate prediction of the transient temperature field based on well-defined boundary conditions representing the dynamic and complex fluid flow inside engines. To meet this requirement, the present study focuses on transient thermomechanical stress analysis using a sequentially coupled computational fluid dynamics (CFD)–finite element analysis (FEA) approach to understand transient thermomechanical responses of the hot surface ignition device. A three-dimensional transient reacting flow simulation was conducted first using converge software, the results of which were exported to map thermal and pressure boundary conditions onto a structural finite element mesh. Transient thermomechanical stress analysis was performed sequentially using abaqus software utilizing the mapped boundary conditions. The results such as transient temperature history, resultant thermomechanical stress, displacement, potential failure modes, etc., were critically reviewed, which can provide helpful information for further design improvement.
5 November 2024 in Journal of Engineering for Gas Turbines and Power
With little drag friction, gas bearings operate at high rotor speed and high temperature and thus enable long operating life along with material damping for mechanical energy dissipation. However, most computational tools for modeling gas bearings are not accessible to bearing manufacturers or potential end-users, and the models are restricted to specific geometries and operating conditions or are missing important features, thus limiting their utility. This paper presents the thermal energy transport in a hybrid gas bearing (HGB) for oil-free turbochargers (TCs) with integrated heat and fluid flow models to produce a comprehensive thermohydrodynamic analysis predictive tool and to design and evaluate air-lubricated gas bearings by predictions and experiments. An efficient algorithm couples the solution of the Reynolds equations and the thermal energy transport equations in the film between the rotor and a pad of the hybrid gas bearing and updates the temperature-dependent viscosity and film thicknesses during the iterative process. The balance of the bulk-flow thermal energy transport is that the summation of drag power losses plus heat convection into the film equals to the thermal energy advected by the film. The predictions show that the film temperature varies along circumferential and axial directions by following the balance of the energy flows and shows high film temperatures corresponding to the small film thicknesses and thus large film pressures. The predicted result also shows that the peak temperature of the film occurs at the exit side of the film near the trailing edge of each pad. Thermocouples installed axially at the leading and trailing edges of each pad measure temperature of the film to validate the thermal module. The test repeats and averaged for each rotor speed from 2 krpm to 22 krpm at intervals of 2 krpm, for supply pressure varying along 25 psi to 100 psi, and predicted film temperature matches well with the measured one. The parameters of interest in this analysis include the gas supply condition, bearing configuration, and the gas properties at high altitudes and high rotation speeds. The parametric study results show that the density and kinematic viscosity are the most dominant properties of the gas lubrication for the film temperature.
20 December 2024 in Journal of Engineering for Gas Turbines and Power
Demand for increased onboard power generation on small aircraft is ever growing due to increased electrical power demand. The objective of this study is to investigate onboard power generation using waste energy at various altitude and ambient conditions. Experiments were performed on a 2-liter, turbocharged direct-injection intermittent combustion engine fueled with jet fuel (F-24). The turbocharger has an integrated motor-generator system that is designed to generate electricity using the enthalpy in the engine exhaust, or to use as a motor to rotate the turbocharger using the energy stored in onboard energy storage device. An electrically actuated wastegate was used to control useful exhaust flowrate that is used to generate electricity. An external power supply system was used to emulate the energy storage. The engine was installed in the U.S. DEVCOM Army Research Laboratory's altitude chamber in which absolute outside air pressure was controlled up to 37.6 kPa to simulate the altitude conditions up to 7,620 m (25,000 ft). Three different ambient conditions were selected to represent International Standard Atmosphere (ISA), polar, and tropical conditions. Based on the experimental results, a response surface model was developed to predict the power generation of the motor-generator integrated turbocharger using waste energy as a function of altitude, engine power, and the wastegate position. The result from this study provides an insight into onboard power generation method using waste energy at altitude conditions.
This paper presents a practical and comprehensive guide for commissioning the controllers of bearingless machines (BMs). While significant research has been conducted on the commissioning of electric machines (EMs) and magnetic bearings (MBs), relatively little attention has been given to bringing up BMs. Motivated by this gap, the paper presents step-by-step methods for commissioning BM control systems. Two major contributions are outlined in the paper. First, static characterization and sensor calibration techniques, which are necessary for levitating the machine, are introduced. Second, a system identification (System ID) procedure for each plant is presented. Frequency response functions (FRFs) are used to identify the control plant transfer function parameters and evaluate the resulting feedback control performance (command tracking and dynamic stiffness). This paper emphasizes practical testing sequences that are immediately applicable to machines. By following the procedures provided in this paper, engineers can efficiently commission BMs by first ensuring precise sensor calibration and accurate models for control tuning.