Sarah Ouerghemmi

Dr. Sarah Ouerghemmi

Leipzig University of Applied Sciences, Leipzig, Saxony, Germany
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 October 2022 in Electronics
Verified
Journal Article
Open access
PDF file
IKIlef Ketata
Ilef Ketata
Sarah OuerghemmiSarah Ouerghemmi
Sarah Ouerghemmi
Ahmed FakhfakhAhmed Fakhfakh
Ahmed Fakhfakh
Faouzi DerbelFaouzi Derbel
Faouzi Derbel
The integration of wireless communication, e.g., in real- or quasi-real-time applications, is related to many challenges such as energy consumption, communication range, quality of service, and reliability. The improvement of wireless sensor networks (WSN) performance starts by enhancing the capabilities of each sensor node. To minimize latencies without increasing energy consumption, wake-up receiver (WuRx) nodes have been introduced in recent works since they can be always-on or power-gated with short latencies by a power consumption in the range of some microwatts. Compared to standard receiver technologies, they are usually characterized by drawbacks in terms of sensitivity. To overcome the limitation of the sensitivity of WuRxs, a design of a low noise amplifier (LNA) with several design specifications is required. The challenging task of the LNA design is to provide equitable trade-off performances such as gain, power consumption, the noise figure, stability, linearity, and impedance matching. The design of fast settling LNA for a duty-cycled WuRx front-end operating at a 868 MHz frequency band is investigated in this work. The paper details the trade-offs between design challenges and illustrates practical considerations for the simulation and implementation of a radio frequency (RF) circuit. The implemented LNA competes with many commercialized designs where it reaches single-stage 12 dB gain at a 1.8 V voltage supply and consumes only a 1.6 mA current. The obtained results could be made tunable by working with off-the-shelf components for different wake-up based application exigencies.

22 March 2021
Verified
Conference Paper
Closed access
Sarah OuerghemmiSarah Ouerghemmi
Sarah Ouerghemmi
IKIlef Ketata
Ilef Ketata
SSSalwa Sahnoun
Salwa Sahnoun
Faouzi DerbelFaouzi Derbel
Faouzi Derbel
Low Noise Amplifiers (LNA) are usually used in the front-end antenna of Radio Frequency (RF) receivers. The LNA boosts the input power and increases the receiver sensitivity with a minimum of noise. Especially for Wake-Up receivers (WuRx), a trade-off between power consumption and sensitivity should be considered. On one side, a high gain should be performed and on the other side, the power consumption should be as low as possible to be able to realize a wireless communication with a minimum of latency. In this work, performed analysis of LNA based on various configurations with transistors are present. The results show that a trade-off between all LNA requirements exists. As Wireless Sensor Networks (WSN) applications face many resource constraints, the selection of adequate component parameters and architectures should be well discussed.

14 June 2025 in Electronics
Verified
Journal Article
Open access
PDF file
Sarah OuerghemmiSarah Ouerghemmi
Sarah Ouerghemmi
Ahmed FakhfakhAhmed Fakhfakh
Ahmed Fakhfakh
Faouzi DerbelFaouzi Derbel
Faouzi Derbel
This paper presents an optimized 868 MHz low-noise amplifier (LNA) based on a bipolar junction transistor (BJT), specifically designed for wake-up receivers operating in the sub-GHz band. The proposed LNA achieves low noise, high gain, and good impedance matching while consuming only 3.2 mA from a 3.3 V supply, resulting in a total power consumption of 10.56 mW. Designing efficient sub-GHz LNAs for low-power applications involves a careful balance between multiple performance metrics. Higher gain typically requires increased biasing current, which can raise power consumption, while achieving a low noise figure often conflicts with input-matching constraints. The presented design addresses these trade-offs by leveraging the BFP740 BJT and employing a stub-based microstrip matching network to simultaneously optimize the gain, noise figure, and input–output matching. Simulation results, using both external lumped elements and microstrip techniques, show a forward gain (S21) of 15.2 dB at 868 MHz, with an input reflection coefficient (S11) of −6.9 dB and an output reflection coefficient (S22) of −6.3 dB. The amplifier achieves a minimum noise figure of approximately 1.77 dB, which is notably low for this frequency band. These results demonstrate that the proposed LNA offers a compact, energy-efficient, and cost-effective solution, ideally suited for always-on, low-power wireless applications such as Internet of Things (IoT) devices and wireless sensor networks.

29 October 2023
Verified
Conference Paper
Closed access
Sarah OuerghemmiSarah Ouerghemmi
Sarah Ouerghemmi
IKIlef Ketata
Ilef Ketata
AFAhmed Fakhfakh
Ahmed Fakhfakh
Faouzi DerbelFaouzi Derbel
Faouzi Derbel
This paper presents an implementation of a wideband low-noise amplifier (LNA) design operating at sub-GHz to be integrated in wireless sensor networks based on Wake-Up receivers to improve the range and latency of peer-to-peer communication. The design requirements meet the needs of Wake-Up Receiver nodes in terms of low power consumption. The design of the low-noise amplifier has been investigated based on appropriate simulations and validated with real measurements based on developed PCBs along the whole frequency band. The LNA delivered a power gain greater than 13 dB below 1 GHz, specifically 15 dB at 868 MHz and 17.45 at 740 MHz. Input and output reflection coefficients respectively were measured as −7.15 dB and −7.99 dB. The stability factor was kept greater than 1 along the whole frequency when the noise figure measurement is below 0.5 dB. With those results the wireless communication between sensor nodes could be improved with regard to range and in comparison to state of the art, the latency could be decreased. So quasi-real time communication even with energy autarkic wireless sensor nodes could be realized.

20 February 2023
Verified
Conference Paper
Closed access
OCOussama Chafai
Oussama Chafai
MNMohamed Wajih Nasri
Mohamed Wajih Nasri
RBRim Barrak
Rim Barrak
Sarah OuerghemmiSarah Ouerghemmi
Sarah Ouerghemmi
IKIlef Ketata
Ilef Ketata
Faouzi DerbelFaouzi Derbel
Faouzi Derbel
This paper presents the design of a Low Noise Amplifier (LNA) for a duty-cycled wake-up receiver operating at 868 MHz frequency band. The LNA is designed using a hetero-junction bipolar transistor. The operating point was selected to realize a trade-off between power consumption, gain, and noise figure with the aim to enhance the wake-up receiver’s sensitivity while maintaining very low power consumption. The transistor was stabilized using the collector feedback biasing technique and matched with lumped components to 50 Ohm impedance. The overall LNA design is a single-stage 19 dB gain consuming only 2 mW from a 1V DC power supply. The simulation results show an input return loss of -12 dB at 868 MHz with a low noise figure of 0.53 dB. The obtained results could be made tunable by working with off-the-shelf components for different wake-up-based application requirements.