Shahid Parvez

Dr. Shahid Parvez

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
Shahid ParvezShahid Parvez
Shahid Parvez
M.I.H. SiddiquiM.I.H. Siddiqui
M.I.H. Siddiqui
MAMasood Ashraf Ali
Masood Ashraf Ali
Dan DobrotaDan Dobrota
Dan Dobrota
A 3D numerical simulation was conducted to study the transient development of temperature distribution in stationary gas tungsten arc welding with filler wire. Heat transfer to the filler wire and the workpiece was investigated with vertical (90°) and titled (70°) torches. Heat flux, current flux, and gas drag force were calculated from the steady-state simulation of the arc. The temperature in the filler wire was determined at three different time intervals: 0.12 s, 0.24 s, and 0.36 s. The filler wire was assumed not to deform during this short time, and was therefore simulated as solid. The temperature in the workpiece was calculated at the same intervals using heat flux, current flux, gas drag force, Marangoni convection, and buoyancy. It should be noted that heat transfer to the filler wire was faster with the titled torch compared to the vertical torch. Heat flux to the workpiece was asymmetrical with both the vertical and tilted torches when the filler wire was fully inserted into the arc. It was found that the overall trends of temperature contours for both the arc and the workpiece were in good agreement. It was also observed that more heat was transferred to the filler wire with the 70° torch compared with the 90° torch. The melted volume of the filler wire (volume above 1750 °K) was 12 mm3 with the 70° torch, compared to 9.2 mm3 with the 90° torch.

1 January 2025 in AIP Advances
Verified
Journal Article
Open access
Shahid ParvezShahid Parvez
Shahid Parvez
MRMagdy M. El Rayes
Magdy M. El Rayes
EAEssam Al-Bahkali
Essam Al-Bahkali
KAKhalid Alqosaibi
Khalid Alqosaibi
This study simulates the pulsed current tungsten inert gas (TIG) welding process to investigate the transient development of the weld pool in a 4 mm thick aluminum sheet, focusing on the effects of pulse frequency on the weld pool size. Two pulsed currents, 230 and 180 A, with a 30% background current, were examined. The 230 A current achieved full, while the 180 A resulted in partial penetration. Five pulse frequencies (1, 4, 10, 20, and 50 Hz) were analyzed. A numerical model was developed to compute heat and current fluxes on the workpiece surface. The arc profile shifted from a bell shape in high-frequency cycles to a conical shape in low-frequency cycles. The heat and current fluxes served as inputs to another model that simulated weld pool behavior for both direct and pulsed current TIG welding. The results showed that weld pool size decreased in pulsed current TIG welding. At 230 A, full penetration changed to partial penetration under pulsed current. At 1 Hz, sufficient time was available for solidification during the low-cycle period, but at 50 Hz, the weld pool remained liquid. As pulse frequency increased from 1 to 50 Hz, the weld pool depth decreased significantly, with a reduction from 2.4 to 0.9 mm at 230 A and from 1.1 to 0.34 mm at 180 A. Convection in the weld pool was influenced by temperature and was strongest at higher temperatures. The decrease in weld pool size was most pronounced between 1 and 10 Hz, stabilizing between 20 and 50 Hz. Validation against experimental macrographs demonstrated good agreement with the simulations.

28 April 2024 in Metals
Verified
Journal Article
Open access
PDF file
Adel AbbasAdel Abbas
Adel Abbas
MHMohamed Hemy
Mohamed Hemy
KAKhalid Alqosaibi
Khalid Alqosaibi
Shahid ParvezShahid Parvez
Shahid Parvez
AHAli Salem Hasan
Ali Salem Hasan
Ahmed ElkaseerAhmed Elkaseer
Ahmed Elkaseer
Despite the prevalent application of 18% Ni maraging steel in critical sectors such as aerospace and automotive due to its unique characteristics, including high ductility, yield strength, and hardenability, its machining presents enormous challenges, categorizing it as a difficult-to-machine material. The cutting tool’s geometry is crucial in machining, significantly affecting chip formation, cutting forces, power consumption, and obtainable surface quality. In particular, wiper insert technology, characterized by its multi-radius design, offers an increased contact area compared to conventional inserts, potentially enhancing the quality of the machined surface. This study explores the effectiveness of wiper inserts in the face-milling of maraging steel 350, conducting a comparative analysis across three distinct machining setups. These setups vary by alternating the number of wiper and conventional inserts within the same cutter, thereby examining the influence of insert configuration on machining outcomes. The research employs a reliable and well-established statistical approach to evaluate how different variables, such as cutting speed and feed rate, affect surface quality, power consumption, and material removal rate (MRR). It also sheds light on the material removal mechanisms facilitated by each type of insert. The findings reveal that incorporating a higher number of wiper inserts significantly enhances the surface finish but concurrently increases power consumption. Thus, the study successfully identifies an optimal set of process parameters that attain a balance between achieving superior surface quality and maintaining energy efficiency in the machining of maraging steel 350. This balance is crucial for optimizing manufacturing processes while adhering to the stringent quality and sustainability standards required in aerospace and automotive manufacturing.

1 September 2025 in Physica Scripta
Verified
Journal Article
Open access
Shahid ParvezShahid Parvez
Shahid Parvez
MRMagdy M. El Rayes
Magdy M. El Rayes
KAKhalid Alqosaibi
Khalid Alqosaibi
EAEssam Al-Bahkali
Essam Al-Bahkali
This study investigates the influence of the duty cycle, with two different torch angles, on the transient development of the weld pool during pulsed current gas tungsten arc welding (PC-GTAW) in lap joints of thin aluminum sheets. A numerical model was developed to accurately evaluate the heat flux, current density, and gas shear stress generated by the arc plasma. These parameters were then used in another model to forecast the weld pool geometry with three pulsed current duty cycles: 20%, 50%, and 80%. Analyses were conducted using torch angles of 20° and 45°. Torch angles significantly affected the arc and weld pool characteristics. Variation in heat flux distribution was observed with the 20° torch yielding higher heat flux on the horizontal surface compared to the vertical, whereas the 45° torch showed slightly high heat flux on the horizontal surface, contrary to symmetry expectations. Results indicate that welding with a 20° torch produced a deeper and wider weld compared to the 45° torch. The 20° torch produced full penetration under the direct current condition, whereas a 45° torch led to partial penetration and asymmetric pool formation due to the joint geometry. Duty cycle also affected the weld pool. At a 20% duty cycle, the weld pool got sufficient time to solidify during each pulse cycle, while at 80% duty cycle, a continuous liquid pool was maintained. Increasing the duty cycle from 20% to 80% developed larger pool sizes for both torch positions. The numerical model was validated with macrostructural images obtained from real experiments giving good agreement between the two. The findings highlight complex interactions between arc plasma dynamics, duty cycle ratios, and weld pool characteristics in PC-GTAW, offering insights for optimizing welding parameters to minimize distortion in thin aluminum sheets in future studies.

Verified
Journal Article
Open access
PDF file
Shahid ParvezShahid Parvez
Shahid Parvez
Three different Gas Tungsten Arc Welding methods—DC single electrode, DC double electrode, and PC double electrode—were analyzed using SS304 steel as the base material. Numerical models were developed to simulate the arc plasmas and calculate heat flux, current density, and wall shear stress on the surface of the workpiece. These data were used as input to simulate the weld pools across all three configurations. Experimental validation showed a good agreement with the numerical results. In the double-electrode setup, electromagnetic interaction caused the arcs to deflect, resulting in an 8% reduction in the maximum heat flux and a 4% decrease in the maximum current density. Marangoni stress had a notable effect on the weld pool shape, creating a -shaped pool with the stationary single-electrode setup, whereas the double-electrode setup produced a -shaped pool after 2 s. In the moving weld pool configurations, the sizes of the pools were maximum at the trailing electrodes. The pool was 1.7 mm deep and 5.6 mm wide in DC double- and 1.4 mm deep and 5.4 mm wide in PC double-electrode configurations. The pool depth and width were only 1.0 mm and 4.2 mm when a DC single-electrode setup was used. Comparing the three methods, the DC double-electrode setup produced the largest pool size. The findings of this research offer guidance for enhancing different arc settings and electrode arrangements to attain the intended welding quality and performance.

11 December 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
Shahid ParvezShahid Parvez
Shahid Parvez
Three different Gas Tungsten Arc Welding methods – DC single-electrode, DC double-electrode, and PC double-electrode – were analyzed using SS304 steel as the base material. Numerical models were developed to simulate the arc plasmas and calculate heat flux, current density, and wall shear stress on the surface of the workpiece. These data served as input for simulating the weld pools across all three configurations. Experimental validation showed a good agreement with the numerical results. In the double-electrode setup, electromagnetic interaction caused the arcs to deflect, which resulting an 8% reduction in the maximum heat flux and a 4% decrease in the maximum current density. Marangoni stress had a notable effect on the weld pool shape, creating a w-shaped stationary pool with the single-electrode setup, whereas the pool reached its greatest depth with the stationary double-electrode configuration. With the moving weld pool, the DC double-electrode created a pool that was 41% deeper and 25% wider compared to the DC single-electrode setup. The PC double-electrode created a pool that was 40% deeper and 22% wider than the DC single-electrode configuration. The findings of the research offer guidance for enhancing different arc settings and electrode arrangements to attain the intended welding quality and performance.