Soran Hassanifard

Dr. Soran Hassanifard

Ryerson University, Faculty of Engineering and Architectural Science

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2021 in Science and Technology of Welding and Joining
Verified
Journal Article
Closed access
AGAmir Ghiasvand
Amir Ghiasvand
SHSoran Hassanifard
Soran Hassanifard
SSS. Saadi
S. Saadi
AVAhmad Varvani-Farahani
Ahmad Varvani-Farahani
This study investigates the influence of tool shapes on tensile properties and microstructural features at stirred zone (SZ) and heat-affected zone of Al 6061 joints welded through friction stir welding (FSW) technique. Six novel dual-pin FSW tools were designed and fabricated consisting of two eccentric pins with different shapes of circle–circle, triangle–triangle (TT), rectangle–rectangle, and the combined pins of circle–triangle, circle–rectangle, and triangle–rectangle. Quasi-static tests were conducted on the welded joint samples and stress–strain data were collected. Dual-pin welding tools led to microstructural evolution including growth in the plastic flow and enlargement in SZ. Weld joints fabricated by TT and rectangle-triangle (RT) tools possessed the maximum values of tensile strength and ductility.

12 October 2021 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
SHSoran Hassanifard
Soran Hassanifard
AGA. Ghiasvand
A. Ghiasvand
AVA. Varvani-Farahani
A. Varvani-Farahani

1 April 2010 in Procedia Engineering
Verified
Journal Article
Open access
SHSoran Hassanifard
Soran Hassanifard
MZMohammad Zehsaz
Mohammad Zehsaz
In this study, resistance spot welding (RSW) process of 5083-O Aluminum alloy has been simulated numerically using an axisymmetric model of electrodes and sheets, and then the effects of residual stresses have been investigated on the fatigue life of the joints. All process parameters except electrode clamping force have been considered to be constant during RSW. Three different electrode force level have been considered and then dimensions of nuggets, HAZ and gaps have been obtained numerically. Three kinds of spot welded models with three different gap values between sheet joints have been simulated using Ansys code. Non-linear analysis was performed to obtain the local stress and strain ranges and then, Morrow equation with particular consideration of residual stress and gap distance effects has been applied to estimate fatigue lives. The results show that, with increasing the electrode force, the gap values between sheet joints increase. The results also reveal that the center region and the roots of nuggets have surrounded by the relatively large amounts of tensile residual stresses and also increasing the electrode force, reduce the amounts of residual stresses. The comparison between numerical results of fatigue lives and experimental data provided good agreement between numerical predictions and experiments

15 November 2014 in Strojniški vestnik - Journal of Mechanical Engineering
Verified
Journal Article
Open access
NANima Jafarzadeh Aghdam
Nima Jafarzadeh Aghdam
SHSoran Hassanifard
Soran Hassanifard
MEMir Mohammad Ettefagh
Mir Mohammad Ettefagh
ANArvin Nanvayesavojblaghi
Arvin Nanvayesavojblaghi

Verified
Journal Article
Open access
PDF file
SHSoran Hassanifard
Soran Hassanifard
AVAhmad Varvani-Farahani
Ahmad Varvani-Farahani
The present study examines the fatigue of friction stir welded (FSW) aluminum 6061, 7075, 1060 joints followed by (i) in situ and sequential rolling (SR) processes, (ii) plastic burnishing (iii) solution-treatment artificial aging (STA), (iv) local alloying through depositing thin copper foils, and (v) inserting alumina powder in the weld nugget zone (NZ). The microstructural features and fatigue life of post-processed joints were compared with those of as-welded joints. The in situ rolling technique offered simultaneous rolling and welding operations of aluminum joints, while through the sequential rolling process, the top surface of FSW joints was rolled after the welding process. The fatigue life of in situ rolled samples was increased as the ball diameter of welding tool increased. The fatigue life of friction stir welded joints after a low-plasticity burnishing process was noticeably promoted. The addition of 1 wt.% alumina in the NZ of joints resulted in a significant elevation on fatigue life of friction stir spot welded joints, while an increase in alumina powder to 2.5 wt.% adversely affected fatigue strength. Weld NZ was alloyed through the insertion of copper foils between the faying surfaces of joints. This localized alloy slightly improved the fatigue life of joints; however, its effects on fatigue life were not as influential as STA heat-treated or in situ rolled joints. The microstructure of weld joints was highly affected through post-processing and treatments, resulting in a substantial influence on the fatigue response of FSW aluminum joints.

29 June 2020 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Verified
Journal Article
Closed access
PDF file
MFM Feyzi
M Feyzi
SHSoran Hassanifard
Soran Hassanifard
AVA Varvani-Farahani
A Varvani-Farahani
The present paper studies fatigue damage and life of single-lap bolted joints tightened with different torque magnitudes subjected to uniaxial load cycles. The adherends were constructed from E-glass/epoxy layers using a hand layup technique and assembled by 1.5, 3, and 8 N m of applied torques. Increasing the torque magnitude benefitted the final fatigue life of the joints so that the high-cycle fatigue life of the joint sample tightened with 8 N m was as high as 10 times that of the joint tightened with 1.5 N m. In the numerical section of this study, a three-dimensional finite element analysis was employed, and the impacts of applied torques were included in the progressive damage model to assess damage and failure in the bolted joints. For the joints tightened with higher torque levels, numerical results revealed higher fatigue lives but at the cost of more delamination at the vicinity of the hole. Laminate fracture surface was investigated through scanning electron microscopy and more cracking/damage progress was evidenced in matrix, fiber, and matrix–fiber interface as composite joints experienced fatigue cycles. Experimental life data of tested joints agreed with those anticipated through the use of finite element analyses indicating the developed model as an appropriate tool in evaluating the effects of applied torques on the fatigue fracture behavior of bolted laminates.