Suherman Suherman

Dr. Suherman Suherman

Diponegoro University

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2021 in Heliyon
Verified
Journal Article
Open access
Hadiyanto HadiyantoHadiyanto Hadiyanto
Hadiyanto Hadiyanto
AKAdian Khoironi
Adian Khoironi
IDInggar Dianratri
Inggar Dianratri
SSSuherman Suherman
Suherman Suherman
FMFuad Muhammad
Fuad Muhammad
SVSeetharaman Vaidyanathan
Seetharaman Vaidyanathan
This study aimed to evaluate the effect of microplastics on Spirulina sp., the pigment phycocyanin in Spirulina sp., and the effect of Spirulina sp. on the degradation of PE and PP plastic. The interaction of Spirulina sp. with microplstic (PE and PP) was conducted by adding the microplastic (500 mg/500 mL, with a size of 0.5–1 mm2) to microalgae culture. The optical density was measured for 30 days to determine the growth of Spirulina sp. Harvesting was performed to obtain dry Spirulina sp biomass. Phycocyanin was obtained through extraction by mixing 0.1 g dry Spirulina sp. biomass with 25 ml of 1% CaCl2 in an ultrasonic water bath at 50 kHz, 300 W at 30 °C for 15 min. The results showed that the growth rate of Spirulina sp significantly decreased (p < 0.05) with treatment of PE (SP + PE) (0.0228/day) and PP (Sp + PP) (0.0221/day), compared to the control (Sp-Control) (0.0312/day). Scanning electron microscopy and Fourier transform infrared spectroscopy (FTIR) analyses of Spirulina sp. biomass with the addition of PE and PP revealed surface damage of Spirulina sp. cells and loss of carboxyl groups from proteins in Spirulina sp. at wavelengths of 1397–1450 cm−1. In addition, Spirulina sp. had decreased the intensity of amine and amide groups from proteins at wavelengths of 3280, 1637, and 1537 cm−1 in the microplastic treatment. The phycocyanin yield and protein content in Spirulina sp. control were 19.69% and 0.147%, respectively, which decreased by 10.7% and 0.121%, respectively, with PE treatment and by 8.7% and 0.108%, respectively, with PP treatment. Moreover, the investigation of PE and PP treated by Spirulina sp showed more significant changes of functional group indicated by the formation of hydroxyl (3286 cm−1), carbonyl (1700 cm−1), ester (1750 cm−1) and primary alcohol (1085 cm−1). The results of the EDX microplastic analysis showed a decrease in carbon in PE (1.62%) and PP (1.08%). These FTIR and EDX analysis also proved that microplastic has experienced degradation when treated by Spirulina sp cell culture.

10 February 2020 in International Journal of Renewable Energy Development
Verified
Journal Article
Open access
PDF file
SSSuherman Suherman
Suherman Suherman
HWHasri Widuri
Hasri Widuri
SPShelyn Patricia
Shelyn Patricia
ESEvan Eduard Susanto
Evan Eduard Susanto
RSRaafi Jaya Sutrisna
Raafi Jaya Sutrisna
In this study, hybrid solar drying of coffee beans was performed, and energy analysis was carried out, to assess the system’s performance, in terms of energy efficiency, compared to solar drying and the open sun drying method. The dryer has three compartments: solar collector for collecting solar radiation, drying chamber, and a Liquid Petroleum Gas burner, which acted as an auxiliary heater to assist the thermal energy. The drying chamber has four trays for placing the dried product. The initial moisture content of coffee beans was 54.23% w.b and was reduced to the final moisture content between 11-12% w.b. The coffee beans dried faster when subjected to the solar hybrid drying method, compared to other methods, with the dryer temperature of 40°C, 50°C, and 60°C. Results indicated that the coffee beans’ drying times varied from 10 to 14 hours. However, at temperature 50°C and 60°C for the 1st tray, the water content was reduced more rapidly compared to the other tray. From the results of this study, we can see the different efficiency of solar collector that shows of 54.15% at variable temperature 60°C for drying time 12:00 to 14:00 p.m for hybrid solar drying and for the solar drying process is 50.07% at the range of drying time 12:00 to 14:00 p.m. Mathematical modelling shows that Page model is the most suitable for describing the coffee beans’ drying behaviour using a hybrid solar dryer. The effective diffusivity values found in this experiment are all in the acceptable range for most agricultural products. ©2020. CBIORE-IJRED. All rights reserved

1 January 2020 in Cogent Engineering
Verified
Journal Article
Open access
SSSuherman Suherman
Suherman Suherman
ESEvan Eduard Susanto
Evan Eduard Susanto
AZAsif Widodo Zardani
Asif Widodo Zardani
NDNur Haniza Roviqoh Dewi
Nur Haniza Roviqoh Dewi
Hadiyanto HadiyantoHadiyanto Hadiyanto
Hadiyanto Hadiyanto
In this study, we aimed to energetically and exergetically evaluate the usage of a hybrid solar dryer system for cassava drying via a series of drying experiments. The experiments were performed beginning at 10.00 A.M. (hereafter, in local time) until the moisture content of cassava starch became constant at a value less than 14% on a wet basis at drying temperatures of 40 °C to 60 °C and drying times of 180–240 min. The results demonstrated that the highest overall dryer energetic efficiency was 20.82%, which was achieved at a drying temperature at 60 °C, and that the maximum energetic efficiency of 27% was recorded at 11.00 A.M. The exergy flows fluctuated during the drying process and were dependent on the solar radiation and drying conditions; however, the exergetic efficiency of the dryer was 25.1%–73.8%. Comparison of the fitting models denoted that the Page model was the most suitable model for describing the experimental drying performances. The calculated effective diffusivity constant (Deff) and the activation energy (Ea) during the drying process from 50 °C to 60 °C were 3·× 10−10 m2/s and 15.3 kJ/mole, respectively.


23 June 2020 in Journal of Food Process Engineering
Verified
Journal Article
Closed access
PDF file
SSSuherman Suherman
Suherman Suherman
Hadiyanto HadiyantoHadiyanto Hadiyanto
Hadiyanto Hadiyanto
ESEvan Eduard Susanto
Evan Eduard Susanto
IUIftitania Ardita Putri Utami
Iftitania Ardita Putri Utami
TNTri Ningrum
Tri Ningrum

1 October 2020 in Heliyon
Verified
Journal Article
Open access
SSSuherman Suherman
Suherman Suherman
Hadiyanto HadiyantoHadiyanto Hadiyanto
Hadiyanto Hadiyanto
ESEvan Eduard Susanto
Evan Eduard Susanto
SRShesar Anis Rahmatullah
Shesar Anis Rahmatullah
APAditya Rofi Pratama
Aditya Rofi Pratama
Lime is one of the most commonly consumed medicinal plants in Indonesia, which must be dried to preserve its quality, but mostly by using traditional, ineffective drying method. Therefore, this study aims to investigate lime drying process a hybrid solar drying method. The hybrid solar dryer consisted of a solar dryer and Liquefied Petroleum Gas as the supplementary heater. The drying process was conducted until there was no significant weight decrease, with the drying temperature of 40, 50, 60, 70, and 80 °C. Thin-layer modeling and quality analysis were also conducted. The experimental results indicated that 5 h was required to sufficiently dry the lime at 80 °C, while drying at 40 °C took 24 h to finish. The drying rate curve of lime suggested that lime drying mostly happened during the falling-rate period. Moreover, the average efficiency of the hybrid solar dryer ranged from 5.36% to 38.61%, which increased with temperature. From the 10 thin-layer drying models used, the Wang and Singh model was the most suitable to describe the drying behavior of lime. The effective diffusivity values of the limes and the activation energy value during hybrid solar drying were within their respective acceptable range for agricultural products. However, as the drying temperature was increased from 40 to 80 °C, the total phenolic content and vitamin C content decreased, from 87.3 to 27.8 mg GAE/100 g dry limes and 0.118 to 0.015 ppm, respectively. It can be concluded that hybrid solar dryer is able to sufficiently dry the lime, with acceptable drying time and dryer efficiency, although using high drying temperature will decrease the quality of dried lime. Further modifications and improvements to the hybrid solar dryer are required to maximize the quality of dried lime while still maintaining fast and effective drying process.