Sukanya Hägg Mameng

Dr. Sukanya Hägg Mameng


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 February 2017 in Corrosion
Verified
Journal Article
Closed access
SMSukanya Hägg Mameng
Sukanya Hägg Mameng
RPRachel Pettersson
Rachel Pettersson
CLChristofer Leygraf
Christofer Leygraf
The influence of the composition of stainless steels on atmospheric corrosion resistance in a marine environment in Dubai was investigated after 2 y and 4 y of exposure. Different stainless steel grades with different surface finishes were included in the investigation: three ferritic stainless steels, five austenitic stainless steels, and four duplex stainless steels. The alloying elements chromium (Cr) and molybdenum (Mo) both had a beneficial influence on the corrosion resistance. The pitting resistance equivalent number (PREN=%Cr + 3.3%Mo + 16%N) and the (%Cr + 3.3%Mo) content in the surface film correlated well to the atmospheric corrosion resistance. An increased Cr content both in the bulk material and in the passive film improved the atmospheric corrosion resistance and the additional presence of Mo was effective in preventing red rust and also reduced the depth of pits. The depth of the pitting attack and the degree of aesthetic degradation were both influenced by alloying level, surface finish, and exposure conditions (open and sheltered). In the severe marine environment in Dubai, it is necessary to use Mo-bearing high-Cr stainless steel for adequate atmospheric corrosion resistance. The most resistant stainless steel grades were the high alloyed grades which ranked in the order UNS S31254 ∼ UNS S3750 < UNS S34565 < UNS S32654. The duplex stainless steel grade S32205 may be considered for construction and architectural materials in Dubai but is likely to require more maintenance.

11 July 2016 in Materials and Corrosion
Verified
Journal Article
Closed access
PDF file
SMSukanya Hägg Mameng
Sukanya Hägg Mameng
RPR. Pettersson
R. Pettersson
JJJ. Y. Jonson
J. Y. Jonson

1 January 2016 in BHM Berg- und Hüttenmännische Monatshefte
Verified
Journal Article
Closed access
PDF file
SMSukanya Hägg Mameng
Sukanya Hägg Mameng
RPRachel Pettersson
Rachel Pettersson
CLChristofer Leygraf
Christofer Leygraf
LWLena Wegrelius
Lena Wegrelius

20 September 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
SMSukanya Hägg Mameng
Sukanya Hägg Mameng
ABAndrew Backhouse
Andrew Backhouse
JMJonathan McCray
Jonathan McCray
GGGraham Gedge
Graham Gedge
The use of duplex stainless steel (DSS) in bridge construction has increased significantly in the last twenty years because of the material's high strength and good corrosion resistance. The high corrosion resistance of DSS results in a low maintenance requirement and hence low life cycle costs. There is now a range of DSS grades available and it is possible during the design phase to undertake a material selection exercise for DSS to align the required material performance with the bridge environment. Lean alloyed and less costly DSS grades can be specified in less harsh environments. This paper presents the results from inspection of various existing road, rail and pedestrian bridges. In each case a DSS was used for the main structure and each bridge illustrates the performance of the material in a representative European environment. The environments were retrospectively classified in accordance with the recently introduced EN 1993-1-4 Annex A and a comparison of actual performance made with the guidance given in this annex. Previous high-level cost studies have indicated that durable, low-maintenance bridge designs using DSS are achievable without incurring excessive initial construction costs, and that significant life cycle cost savings can be made over the life of the structure. The present work has confirmed that, when appropriately selected and used, DSS can be anticipated to give long service lives in bridge structures, greatly reducing corrosion problems that may necessitate re-painting and remediation of carbon steel structures.

11 April 2024 in Frontiers in Materials
Verified
Journal Article
Open access
SMSukanya Hägg Mameng
Sukanya Hägg Mameng
LWLena Wegrelius
Lena Wegrelius
SHSaman Hosseinpour
Saman Hosseinpour
Introduction: This work systematically investigates the effect of chloride level, temperature, and the water system’s oxidative power on the pitting corrosion performance of stainless steels in pH-neutral environments.Methods: Two test programs were set to a) develop a robust method for constructing the pitting engineering diagrams and b) construct the pitting engineering diagrams based on the obtained method from the first test program. The various electrochemical techniques were selected to assess and understand factors that affect the corrosion behavior of stainless steel. Extensive testing was performed with short-term electrochemical measurements and long-term immersion tests.Results and Discussion: The obtained results demonstrate that the electrochemical methods are sufficient to define pitting diagrams showing the boundaries between pitting and no pitting as a function of chloride concentration, temperature, and the water system’s oxidation potential. The laboratory long-term electrochemical test results correspond the best to real applications and clearly underline the importance of an induction time for pit initiation. Accordingly, two sets of pitting engineering diagrams were constructed based on the water system’s oxidation potential. Measurements at the applied potential of 150 mV vs. saturated calomel electrode (SCE) correspond to applications in sterile tap water, whereas the applied potential of 400 mV vs. SCE corresponds to slightly chlorinated water or water with some biological activity. Pitting engineering diagrams were proved to be very useful tools to aid material selection in water application. However, it is important to realize that additional factors, such as different surface conditions and the presence of other environmental species, crevice design, or weld will affect the exact position of the boundaries between pitting and no pitting.

Verified
Journal Article
Open access
PDF file
Saman HosseinpourSaman Hosseinpour
Saman Hosseinpour
SMSukanya Hägg Mameng
Sukanya Hägg Mameng
MAMarie Almen
Marie Almen
MLMia Liimatainen
Mia Liimatainen
Owing to its corrosion resistance, stainless steel is a sustainable alternative to carbon steel as a structural material in challenging seawater environments. Studies on carbon steel indicate that among all marine corrosion zones (i.e., atmospheric zone, splash zone, tidal zone, and immersed zone), the rate of corrosion is particularly high in the splash zone, above the seawater level, due to the recurrent splashing of seawater with high levels of oxygen and chloride content. Nevertheless, the information on the extent of localized corrosion (i.e., pitting and crevice corrosion) on stainless steel in the splash and tidal zones is scarce and, in most cases, limited to standard austenitic grades. In this work, we present the pitting and crevice corrosion results on lean duplex, duplex, and super duplex stainless steels after two years of field exposure in the North Sea (site at Heligoland South Harbour). The standard austenitic grade 1.4404 (316L) was also exposed as a reference material in atmosphere and splash zone conditions. Parallel exposure of coupons in splash, tidal, and immersed zones allows comparison of the extent of corrosion in each zone and enables proper material selection for structural applications in marine environments.