Taeyoon Eom

Mr. Taeyoon Eom

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 July 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JLJohn LaRocco
John LaRocco
TETaeyoon Eom
Taeyoon Eom
ESEkansh Seth
Ekansh Seth
VGVania Gandhi
Vania Gandhi
ABAnna Bontempo
Anna Bontempo
EZEric Zachariah
Eric Zachariah
Non-invasive transcranial electrical stimulation is a category of neuromodulation techniques used for various disorders. Although medically approved devices exist, the variety of consumer electrical stimulation devices is increasing. Because clinical trials and animal tests are costly and risky, using a brain phantom can provide preliminary experimental validation. However, existing brain phantoms are often costly or require excessive preparation time, precluding their use for rapid, real-time optimization of stimulation settings. A limitation of direct electric fields in a phantom is the lack of 3D spatial resolution. Using well-researched modalities such as transcranial direct current stimulation (tDCS) and newer modalities such as amplitude-modulated transcranial pulsed-current stimulation (am-tPCS), a range of materials was tested for use as electrical phantoms. Based on cost, preparation time, and efficiency, ground beef and agar gel with a 10% salt mix were selected. The measured values for the total dosages were 0.55 W-s for am-tPCS and 0.91 W-s for tDCS. Due to a low gain on the recording electrodes, the signal efficiency measured against the power delivered was 4.2% for tDCS and 3.1% for am-tPCS. Issues included electrodes shifting in the soft material and the low sensitivity of the recording electrodes. Despite these issues, the effective combination of the phantom and recording methodologies can enable low costs and the rapid testing, experimentation, and verification of consumer neuromodulation devices in three dimensions. Additionally, the efficiency factors (EFs) between the observed dosage and the delivered dosage could streamline the comparison of experimental configurations. As demonstrated by comparing two types of electrical neuromodulation devices across the 3D space of a phantom, EFs can be used in conjunction with a cost-effective, time-expedient phantom to rapidly iterate and optimize stimulation parameters.

14 May 2025 in Technologies
Verified
Journal Article
Open access
PDF file
JLJohn LaRocco
John LaRocco
TETaeyoon Eom
Taeyoon Eom
TDTanush Duggisani
Tanush Duggisani
IZIan Zalcberg
Ian Zalcberg
JXJinyi Xue
Jinyi Xue
EZEric Zachariah
Eric Zachariah
Concussion is a costly healthcare issue affecting sports, industry, and the defense sector. The financial impacts, however, extend beyond acute medical expenses, affecting an individual’s physical and cognitive abilities, as well as increasing the burden on coworkers, family members, and caregivers. More effective personal protective equipment may greatly reduce the risk of concussion and injury. Notably, aerogels are light, but traditionally fragile, non-Newtonian fluids, such as shear-thickening fluids, which generate more resistance when compressive force is applied. Herein, a composite material was developed by baking a shear-thickening fluid (i.e., starch) and combining it with a commercially available aerogel foam, thus maintaining a low cost. The samples were tested through the use of a ballistic pendulum system, using a spring-powered launcher and a gas-powered cannon, followed by ballistic penetration testing, using two electromagnetic accelerators and two different projectiles. During the cannon tests without a hardhat, the baked composite only registered 31 ± 2% of the deflection height observed for the pristine aerogel. The baked composite successfully protected the hygroelectric devices from coilgun projectiles, whereas the projectiles punctured the pristine aerogel. Leveraging the low-cost design of this new composite, personal protective equipment can be improved for various sporting, industrial, and defense applications.