Tihomir Sashev Brusev

Prof. Dr. Tihomir Sashev Brusev

Faculty of Telecommunications, TMCS, Technical University of Sofia, Sofia, Sofia-Grad, Bulgaria
orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 September 2024 in Sensors
Verified
Journal Article
Open access
PDF file
RMRosen Miletiev
Rosen Miletiev
Peter Z. PetkovPeter Z. Petkov
Peter Z. Petkov
RYRumen Yordanov
Rumen Yordanov
TBTihomir Sashev Brusev
Tihomir Sashev Brusev
The development of unmanned ground vehicles and unmanned aerial vehicles requires high-precision navigation due to the autonomous motion and higher traffic intensity. The existing L1 band GNSS receivers are a good and cheap decision for smartphones, vehicle navigation, fleet management systems, etc., but their accuracy is not good enough for many civilian purposes. At the same time, real-time kinematic (RTK) navigation allows for position precision in a sub-centimeter range, but the system cost significantly narrows this navigation to a very limited area of applications, such as geodesy. A practical solution includes the integration of dual-band GNSS receivers and inertial sensors to solve high-precision navigation tasks, but GNSS position accuracy may significantly affect IMU performance due to having a great impact on Kalman filter performance in unmanned vehicles. The estimation of dilution-of-precision (DOP) parameters is essential for the filter performance as the optimality of the estimation in the filter is closely connected to the quality of a priori information about the noise covariance matrix and measurement noise covariance. In this regard, the current paper analyzes the DOP parameters of the latest generation dual-band GNSS receivers and compares the results with the L1 ones. The study was accomplished using two types of antennas—L1/L5 band patch and wideband helix antennas, which were designed and assembled by the authors. In addition, the study is extended with a comparison of GNSS receivers from different generations but sold on the market by one of the world’s leading GNSS manufacturers. The analyses of dilution-of-precision (DOP) parameters show that the introduction of dual-band receivers may significantly increase the navigation precision in a sub-meter range, in addition to multi-constellation signal reception. The fast advances in the performance of the integrated CPU in GNSS receivers allow the number of correlations and tracking satellites to be increased from 8–10 to 24–30, which also significantly improves the position accuracy even of L1-band receivers.

1 May 2008
Verified
Conference Paper
Closed access
TBTihomir Sashev Brusev
Tihomir Sashev Brusev
PGPeter Goranov
Peter Goranov
MHMarin Hristov
Marin Hristov
Buck converter for low power applications is designed and investigated on standard 0.35-mum CMOS process. The blocks of the system, including bandgap reference, ramp generator, error amplifier, comparator, buffer and power buck stage, are optimized using CADENCE design tools. The energy losses in the controlling stages are minimized in order to improve the overall converter efficiency eta. A relatively high switching frequency of about 147 MHz is used in order to decrease the size of the filtering components. Power efficiency of about 70% is achieved for voltage conversion from 3.6 V down to 1.2 V. The converter systems shows stable performance over temperature, input voltage, and output load variations.

1 September 2019
Verified
Conference Paper
Closed access
MSMariya Spasova
Mariya Spasova
TBTihomir Sashev Brusev
Tihomir Sashev Brusev
GAGeorge Angelov
George Angelov
RRRossen Radonov
Rossen Radonov
MHMarin Hristov
Marin Hristov
In this paper we compare low power ramp generator schematics realized with conventional MOSFET transistors and CNTFET transistors. The current consumption and power losses of the both circuits are evaluated and analyzed. The generator circuit is part of an overall buck dc-dc converter system, which uses a PWM control technique. The investigation is performed in Cadence Spectre circuit simulator using the 0.35 µm CMOS technology design kit.

1 August 2008
Verified
Conference Paper
Closed access
TBTihomir Sashev Brusev
Tihomir Sashev Brusev
MHMarin Hristov
Marin Hristov
Monolithic switching buck (step-down) converter is designed on standard 0.35-mum CMOS process. Different control techniques such as Pulse-Width Modulations (PWM) and Pulse-Frequency Modulations (PFM) are investigated. The received results show that PFM control indicates higher efficiency at light-loads compare to standard constant frequency PWM control. Efficiency of about 76% is achieved for the PWM control at switching frequency of 150 MHz for voltage conversion from 3.6 down to 1.2 V.

16 June 2022
Verified
Conference Paper
Closed access
TBTihomir Sashev Brusev
Tihomir Sashev Brusev
In this paper an integrated buck switching-mode regulator for modern communication portable devices is presented. The switching frequency $f_{s}$ of the circuit, designed on AMS 0.35 µm technology with Cadence, is equal to 200 MHz. Power losses sources in CMOS IC are discussed and evaluated as a function of circuits parameter. The energy dissipations and efficiency of the designed converter are investigated as a function of the load current $I_{L}$.

1 October 2017
Verified
Conference Paper
Closed access
GKGeorgi Kunov
Georgi Kunov
TBTihomir Sashev Brusev
Tihomir Sashev Brusev
EGElissaveta Gadjeva
Elissaveta Gadjeva
Multiphase ZVS BUCK DC-DC Converter with Voltage Mode Peak Current Control is proposed in the present paper. In this way, the advantages of Multiphase Converters and Zero Voltage Switching (ZVS) Converters are combined. The proposed Control System provides constant phase shifting between individual DC-DC converters when the peak value of the current varies, as a result of which the switching frequency also changes. The transient process at the start of the converter is simulated, as well as the response of the voltage regulator to a sudden change in load. Using parametric analysis, the optimal parameter values of the compensating circuit elements of the voltage regulator are determined.