The aim of this article is to analyze classical flutter and active control of single-cell thin-walled composite wind turbine blade beam based on piezoelectric actuation. Effects of piezoelectric actuation for classical flutter suppression on wind turbine blade beam subjected to combined transverse shear deformation, warping restraint effect, and secondary warping are investigated. The extended Hamilton’s principle is used to set up the equations of motion, and the Galerkin method is applied to reduce the aeroelastic coupled equations into a state-space form. Active control is developed to enhance the vibrational behavior and dynamic response to classical aerodynamic excitation and stabilize structures that might be damaged in the absence of control. Active optimal control scheme based on linear quadratic Gaussian (LQG) controller is implemented. The research provides a way for rare study of classical flutter suppression and active control of wind turbine blade based on piezoelectric actuation.
The aim of this paper is to analyze aeroelastic stability, especially flutter suppression for aeroelastic instability. Effects of aeroservoelastic pitch control for flutter suppression on wind turbine blade section subjected to combined flap and lag motions are rarely studied. The work is dedicated to solving destructive flapwise and edgewise instability of stall-induced flutter of wind turbine blade by aeroservoelastic pitch control. The aeroelastic governing equations combine a flap/lag structural model and an unsteady nonlinear aerodynamic model. The nonlinear resulting equations are linearized by small perturbation about the equilibrium point. The instability characteristics of stall-induced flap/lag flutter are investigated. Pitch actuator is described by a second-order model. The aeroservoelastic control is analyzed by three types of optimal PID controllers, two types of fuzzy PID controllers, and neural network PID controllers. The fuzzy controllers are developed based on Sugeno model and intuition method with good results achieved. A single neuron PID control strategy with improved Hebb learning algorithm and a radial basic function neural network PID algorithm are applied and performed well in the range of extreme wind speeds.
Numerical simulation of a novel fuzzy control and back propagation neural network (BPNN) control for divergent instability based on classical flutter of 5-DOF wind turbine blade section driven by pitch adjustment has been investigated. The work is dedicated to solving destructive flap/lag/twist divergent instability from classical flutter, which might occur during the gust wind action, and might cause fracture failure of the blade itself and tower body. In order to investigate the optimal control method, the parameters of blade section are specially designed so as to simulate the actual situation, which lead to absolutely divergent motions (ADM) under gust wind load. The control of ADM often leads to limit cycle oscillation (LCO), the larger amplitude of which is likely to cause fracture failure of tower body. A novel fuzzy control method with adjustable quantization gain and BPNN control strategy are investigated in order to effectively eliminate LCO (leading to direct convergence of the system) or reduce the amplitude of LCO. The obvious effects of fuzzy control and BPNN control are illustrated by numerical comparisons of vibration suppression from nonlinear time response, amplitude of LCO and frequency spectrum analysis. An experimental platform is built based on hardware-in-the-loop simulation by way of PLC-OPC technology in order to test the real-time performance of the control algorithm. The feasibility of the control algorithm is demonstrated by the experimental results displayed by touch-screen hardware.
2 July 2018 in Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering
System modeling and aeroservoelastic control for divergent instability of stall-induced composite wind turbine blade modeled as thin-walled symmetric layup beam analysis have been investigated based on hydraulic pitch system and radial basic function neural network control. The blade is modeled as single-cell thin-walled beam structure with the circumferentially asymmetric stiffness design, exhibiting flap/lead-lag bending coupling deformation. The stall flutter and aeroservoelastic control of composite blade are investigated based on dynamic stall Beddoes–Leishman aerodynamic model and radial basic function neural network proportional–integral–derivative controller, with pitch actuator performed by hydraulic system. The system motion equations consist of the aeroelastic equations and the six-order pitch equation. The nonlinear aeroelastic responses, including both flap/lead-lag responses and pitch angle responses under different parameters, are solved by Galerkin method and the nonlinear time integration scheme with nonlinear residual analysis. To verify the effectiveness of the control scheme and realize visualized display of large thin-walled blade in the laboratory, experimental platform based on hardware-in-the-loop simulation is built to realize real-time control and virtual simulation. The platform structure consists of PLC hardware, monitoring interface in configuration software, and simulation environment that is connected by the OPC server with PLC system. The platform lays the foundation for vibrational behavior research on visualization of large wind turbine blade under divergent stall situation and verifies the real-time feasibility of the control algorithm proposed.