Yue Liu

Dr. Yue Liu

Louisiana State University Agricultural Center, Baton Rouge, Louisiana, USA
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2019 in Theriogenology
Verified
Journal Article
Closed access
Yue LiuYue Liu
Yue Liu
HBHarvey Blackburn
Harvey Blackburn
STSabrina S. Taylor
Sabrina S. Taylor
TTTerrence Tiersch
Terrence Tiersch

1 April 2014 in Gene
Verified
Journal Article
Closed access
XLXilei Li
Xilei Li
ZBZhiyi Bai
Zhiyi Bai
HLHongrui Luo
Hongrui Luo
Yue LiuYue Liu
Yue Liu
GWGuiling Wang
Guiling Wang
JLJiale Li
Jiale Li

1 December 2017 in Zebrafish
Verified
Journal Article
Closed access
LTLeticia Torres
Leticia Torres
Yue LiuYue Liu
Yue Liu
AGAmy Guitreau
Amy Guitreau
HYHuiping Yang
Huiping Yang
TTTerrence Tiersch
Terrence Tiersch
Quality control (QC) is essential for reproducible and efficient functioning of germplasm repositories. However, many biomedical fish models present significant QC challenges due to small body sizes (<5 cm) and miniscule sperm volumes (<5 μL). Using minimal volumes of sperm, we used Zebrafish to evaluate common QC endpoints as surrogates for fertilization success along sequential steps of cryopreservation. First, concentrations of calibration bead suspensions were evaluated with a Makler® counting chamber by using different sample volumes and mixing methods. For sperm analysis, samples were initially diluted at a 1:30 ratio with Hanks' balanced salt solution (HBSS). Motility was evaluated by using different ratios of sperm and activation medium, and membrane integrity was analyzed with flow cytometry at different concentrations. Concentration and sperm motility could be confidently estimated by using volumes as small as 1 μL, whereas membrane integrity required a minimum of 2 μL (at 1 × 106 cells/mL). Thus, <5 μL of sperm suspension (after dilution to 30–150 μL with HBSS) was required to evaluate sperm quality by using three endpoints. Sperm quality assessment using a combination of complementary endpoints enhances QC efforts during cryopreservation, increasing reliability and reproducibility, and reducing waste of time and resources.

15 February 2022 in Fishes
Verified
Journal Article
Open access
PDF file
NZNikolas C. Zuchowicz
Nikolas C. Zuchowicz
JBJorge Alfonso Belgodere
Jorge Alfonso Belgodere
Yue LiuYue Liu
Yue Liu
ISIgnatius Semmes
Ignatius Semmes
WMWilliam Monroe
William Monroe
TTTerrence Tiersch
Terrence Tiersch
Germplasm repositories can benefit sustainable aquaculture by supporting genetic improvement, assisted reproduction, and management of valuable genetic resources. Lack of reliable quality management tools has impeded repository development in the past several decades. Microfabricated open-hardware devices have emerged as a new approach to assist repository development by providing standardized quality assessment capabilities to enable routine quality control. However, prototyping of microfabricated devices (microdevices) traditionally relies on photolithography techniques that are costly, time intensive, and accessible only through specialized engineering laboratories. Although resin 3-D printing has been introduced into the microfabrication domain, existing publications focus on customized or high-cost (>thousands of USD) printers. The goal of this report was to identify and call attention to the emerging opportunities to support innovation in microfabrication by use of low-cost (<USD 350) resin 3-D printing for rapid prototyping. We demonstrate that low-cost mask-based stereolithography (MSLA) 3-D printers with straightforward modifications can provide fabrication quality that approaches traditional photolithography techniques. For example, reliable feature sizes of 20 µm with dimensional discrepancy of <4% for lateral dimensions and <5% for vertical dimensions were fabricated with a consumer-level MSLA printers. In addition, alterations made to pre-processing, post-processing, and printer configuration steps improved print quality as demonstrated in objects with sharper edges and smoother surfaces. The prototyping time and cost of resin 3-D printing (3 h with USD 0.5/prototype) were considerably lower than those of traditional photolithography (5 d with USD 80/prototype). With the rapid advance of consumer-grade printers, resin 3-D printing can revolutionize rapid prototyping approaches for microdevices in the near future, facilitating participation in interdisciplinary development of innovative hardware to support germplasm repository development for aquatic species.

4 August 2021 in Journal of Applied Aquaculture
Verified
Journal Article
Closed access
WCWilliam M. Childress
William M. Childress
Yue LiuYue Liu
Yue Liu
TTTerrence Tiersch
Terrence Tiersch
Efforts in development of germplasm repositories to preserve genetic resources of aquatic species are impeded globally by a lack of standardized, inexpensive, reproducible, and portable cryopreservation technologies. The present work demonstrates a 3-D printed standardizable freezing device that can be used with nitrogen vapor shipping dewars for on-site sperm cryopreservation for aquatic species and be distributed as open-hardware. This device could hold 22 French straws (0.25-mL or 0.5-mL) and a quick-release ring design could eject straws directly into a canister inside a dewar by pressing a button after freezing. The final prototypes produced cooling rates of 1 to 68°C/min for 0.25-mL straws, and 3 to 37°C/min for 0.5-mL straws with a material cost of 3.5 USD for a single device and 1,820–2,562 USD for batch production of 20 replicates (including labor and purchase of 3-D printers). Progressing through design, prototyping, and testing was delineated to help guide the development of open-source devices within cryopreservation user communities.

15 February 2013 in Aquaculture International
Verified
Journal Article
Closed access
PDF file
YZYongchao Zhao
Yongchao Zhao
ZBZhiyi Bai
Zhiyi Bai
LFLonglong Fu
Longlong Fu
Yue LiuYue Liu
Yue Liu
GWGuiling Wang
Guiling Wang
JLJiale Li
Jiale Li