Fractured karstic carbonate reservoirs have obvious multi-scale characteristics and severe heterogeneity due to the development of abundant karst caves and fractures with different scales. Darcy and non-Darcy flows coexist due to this property. Therefore, selecting the appropriate flow equations for different regions in the numerical simulation of fluid flows, particularly two-phase and multiphase flows, is a critical topic. This paper compares and analyses the displacement distance differences of waterfront travel using the Darcy, Forchheimer and Barree–Conway equations, as well as analyzes the influence of the Forchheimer constant, fluid viscosity, flow rate and absolute permeability on inertia action based on the Buckley–Leverett theory. The results show that the Forchheimer number/Reynolds number of water/oil two-phase flow is not a constant value and varies with water saturation, making it difficult to determine whether the inertial action should be considered solely based on these values; the influence of inertial action can be measured well by comparing the difference between the displacement distances of the waterflood front, and the quantitative standard is given for the selection of the flow equation of different regions by calculating the allowable error of the displacement distance of the waterflood front. The magnitude of the inertial effect is affected by the physical properties of the fluid and reservoir medium and the fluid velocity. The smaller the difference in the viscosity of the oil/water fluid, the smaller the inertial effect is. This technique was used a preliminary attempt to analyze the fractured karstic carbonate reservoirs at Tarim, and the results confirmed the validity of the method described in this article.
Addressing the critical challenges of sealing integrity and operational optimization in aquifer gas storage (AGS), this study focuses on a block within the Qianjiang Basin to systematically investigate geological modeling and injection–production strategies. Utilizing 3D seismic interpretation, drilling, and logging data, a stochastic geological modeling approach was employed to construct a high-resolution 3D reservoir model, elucidating the distribution of reservoir properties and trap configurations. Numerical simulations optimized the gas storage parameters, yielding an injection rate of 160 MMSCF/day (40 MMSCF/well/day) over 6-month-long hot seasons and a production rate of 175 MMSCF/day during 5-month-long cold seasons. Interval theory was innovatively applied to assess fault stability under parameter uncertainty, determining a maximum safe operating pressure of 23.5 MPa—12.3% lower than conventional deterministic results. The non-probabilistic reliability analysis of caprock integrity showed a maximum 11.1% deviation from Monte Carlo simulations, validating the method’s robustness. These findings establish a quantitative framework for site selection, sealing system evaluation, and operational parameter design in AGS projects, offering critical insights to ensure safe and efficient gas storage operations. This work bridges theoretical modeling with practical engineering applications, providing actionable guidelines for large-scale AGS deployment.
Isolated fractures usually exist in fractured media systems, where the capillary pressure in the fracture is lower than that of the matrix, causing the discrepancy in oil recoveries between fractured and non-fractured porous media. Experiments, analytical solutions and conventional simulation methods based on the continuum model approach are incompetent or insufficient in describing media containing isolated fractures. In this paper, the simulation of the counter-current imbibition in fractured media is based on the discrete-fracture model (DFM). The interlocking or arrangement of matrix and fracture system within the model resembles the traditional discrete fracture network model and the hybrid-mixed-finite-element method is employed to solve the associated equations. The Behbahani experimental data validates our simulation solution for consistency. The simulation results of the fractured media show that the isolated-fractures affect the imbibition in the matrix block. Moreover, the isolated fracture parameters such as fracture length and fracture location influence the trend of the recovery curves. Thus, the counter-current imbibition behavior of media with isolated fractures can be predicted using this method based on the discrete-fracture model.
To address brine discharge pipe blockage caused by salt crystallization in natural gas storage facilities within salt caverns, this study employed GROMACS molecular dynamics simulations to develop a three-dimensional regulatory model integrating interfacial polarity, roughness, and diffusion fields. By constructing and comparing four representative interface models, rough iron, smooth iron, epoxy resin, and polytetrafluoroethylene interfaces in sodium chloride solution, the study systematically revealed the coupled microscopic mechanisms of ion adsorption, diffusion, and ordering. The rough iron interface exhibits a nanotrapping effect, increasing the sodium ion concentration to 3.8 times that of the bulk solution. In contrast, the epoxy resin interface forms a hydrated buffer layer, thereby reducing adsorption energy. Conversely, the PTFE interface exhibits superior anti-crystallization performance, extending the induction period by 3.2 times through synergistic effects of ultra-low adsorption energy, high diffusion coefficient, and weak interfacial tension. By integrating these key parameters, an innovative interfacial anti-crystallization index was established, exhibiting a significant negative correlation with crystallization mass in experiments. Furthermore, a nanostructure modification strategy featuring nano-pore arrays was proposed. This approach reduces effective adsorption sites while enhancing ion diffusion rates, thereby decreasing crystallization rates. Such atomically precise control offers novel pathways for designing advanced anti-crystallization coatings.
The behavior of brine solution in the porous media of the strata is of great significance for geological environment regulation. In this study, a molecular dynamics model with silicon dioxide walls was constructed to reveal the regulatory mechanism of the natural potential of the electric field on cluster aggregation. It was found that the critical electric field intensity was 7 V/m. When the electric field intensity was lower than this value, the aggregation rate was only increased by 0.73 times due to thermal motion; when it was higher than this value, the rate increased sharply by 3.2 times due to the dominant effect of electric field force. The microscopic structure analysis indicated that the strong electric field induced the transformation of clusters from fractal structure into an amorphous structure (the index of the order degree increased by 58%). The directional regulation experiments confirmed that the axial electric field led to anisotropic growth (the index of uniformity increased by 0.58 ± 0.04), and the rotational electric field could achieve a three-dimensional uniform distribution (the index of uniformity increased by 42%). This study provides theoretical support for the regulation of brine behavior and the optimization of geological energy storage.