Yutao Qin

Dr. Yutao Qin

University of Michigan, Ann Arbor
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 February 2016 in Microsystems & Nanoengineering
Verified
Journal Article
Open access
Yutao QinYutao Qin
Yutao Qin
YGYogesh B Gianchandani
Yogesh B Gianchandani
This paper reports a complete micro gas chromatography (μGC) system in which all the components are lithographically microfabricated and electronically interfaced. The components include a bi-directional Knudsen pump, a preconcentrator, separation columns and a pair of capacitive gas detectors; together, these form the iGC3.c2 system. All the fluidic components of the system are fabricated by a common three-mask lithographic process. The Knudsen pump is a thermomolecular pump that provides air flow to the μGC without any moving parts. The film heaters embedded in the separation columns permit temperature programming. The capacitive detectors provide complementary response patterns, enhancing vapor recognition and resolving co-eluting peaks. With the components assembled on printed circuit boards, the system has a footprint of 8×10 cm2 . Using room air as the carrier gas, the system is used to experimentally demonstrate the analysis of 19 chemicals with concentration levels on the order of parts per million (p.p.m.) and parts per billion (p.p.b.). The tested chemicals include alkanes, aromatic hydrocarbons, aldehydes, halogenated hydrocarbons and terpenes. This set of chemicals represents a variety of common indoor air pollutants, among which benzene, toluene and xylenes (BTX) are of particular interest.

1 June 2015 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
SASeungdo An
Seungdo An
Yutao QinYutao Qin
Yutao Qin
YGYogesh B. Gianchandani
Yogesh B. Gianchandani
This paper describes the analysis, design, and microfabrication of a Knudsen pump for high flow generation. The Knudsen pump generates gas streams from the cold end to the hot end using free-molecular flow without moving parts. The designed Knudsen pump has densely arrayed vertically oriented 2-μm wide rectangular channels for providing high flow. The temperature gradient is provided between a thin-film metal heater and a gridded Si heat sink in the Knudsen pump structure. The Knudsen pump is fabricated on a single silicon-on-insulator wafer using a four-mask lithographic process. The sidewalls of the rectangular channels are constructed by atomic layer deposition of Al 2 O 3 on sacrificial Si channels and subsequent Si etching. The fabricated Knudsen pumps have designed footprints ranging from 0.4-3.2 cm 2 . At atmospheric pressure, the fabricated Knudsen pumps provide a maximum measured air flow rate of >200 sccm with response time of <;0.5 s. Experimental results have also shown that these Knudsen pumps are most suitable for pumping at moderate vacuum pressure of ≈200 Torr (27 kPa).

13 January 2023 in Analytical Chemistry
Verified
Journal Article
Closed access
WLWeilin Liao
Weilin Liao
DWDeclan Winship
Declan Winship
ILIrene Lara-Ibeas
Irene Lara-Ibeas
XZXiangyu Zhao
Xiangyu Zhao
QXQu Xu
Qu Xu
YGYogesh B. Gianchandani
Yogesh B. Gianchandani

15 October 2015 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Open access
PDF file
Yutao QinYutao Qin
Yutao Qin
SASeungdo An
Seungdo An
YGYogesh B Gianchandani
Yogesh B Gianchandani
This paper reports an evaluation and a comparison of two architectures for implementing Si-micromachined high-flow Knudsen pumps. Knudsen pumps, which operate on the principle of thermal transpiration, have been shown to have great promise for micro-scale gas phase fluidic systems such as micro gas chromatographs. Simultaneously achieving both a high flow rate and adequate blocking pressure has been a persistent challenge, which is addressed in this work by combining multiple pumps in series and addressing the resulting challenges in thermal management. The basic building block is a Si-micromachined pump with ≈100 000 parallel channels in a 4 mm × 6 mm footprint. In the primary approach, multiple pump stages are stacked vertically with interleaved Si-micromachined spacers. A stacked 4-stage Knudsen pump has a form factor of 10 mm × 8 mm × 6 mm. In an alternate approach, multiple stages are arranged in a planar array. The experimental results demonstrate multiplication of the output pressure head with the number of stages, while the flow rate is maintained. For example, a stacked 4-stage Knudsen pump with 8 W power operated at atmospheric pressure provided a blocking pressure of 0.255 kPa, which was 3.6 × of that provided by a single-stage pump with 2 W power; while both provided a ≈ 30 sccm maximum flow rate. The performance can be customized for practical applications such as micro gas chromatography.

15 December 2023 in Journal of Chromatography A
Verified
Journal Article
Closed access
XZXiangyu Zhao
Xiangyu Zhao
RARyan Aridi
Ryan Aridi
JHJacob Hume
Jacob Hume
SSSwetha Subbiah
Swetha Subbiah
XWXingqi Wu
Xingqi Wu
YGYogesh B. Gianchandani
Yogesh B. Gianchandani

6 January 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
QCQisen Cheng
Qisen Cheng
Yutao QinYutao Qin
Yutao Qin
YGYogesh B. Gianchandani
Yogesh B. Gianchandani
This paper reports on a bidirectional Knudsen pump (KP) with a 3D-printed thermal management platform; the pump is intended principally for microscale gas chromatography applications. Knudsen pumps utilize thermal transpiration, where non-viscous flow is created against a temperature gradient; no moving parts are necessary. Here, a specialized design leverages 3D direct metal laser sintering and provides thermal management that minimizes loss from a joule heater located on the outlet side of KP, while maintaining convective cooling on the inlet side. The 3D-KP design is integrative and compact, and is specifically intended to simplify assembly. The 3D-KP pumping area is ≈1.1 cm2; with the integrated heat sink, the structure has a footprint of 64.2 × 64.2 mm2. Using mixed cellulose ester (MCE) membranes with a 25 nm average pore diameter and 525 μm total membrane thickness as the pumping media, the 3D-KP achieves a maximum flow rate of 0.39 sccm and blocking pressure of 818.2 Pa at 2 W input power. The operating temperature is 72.2 °C at ambient room temperature. In addition to MCE membranes, anodic aluminum oxide (AAO) membranes are evaluated as the pumping media; these AAO membranes can accommodate higher operating temperatures than MCE membranes. The 3D-KP with AAO membranes with 0.2 μm average pore diameter and 531 μm total membrane thickness achieves a maximum flow rate of 0.75 sccm and blocking pressure of 496.1 Pa at 9.8 W at an operating temperature of 191.2 °C.