Yutong Liu

Mr. Yutong Liu

Chang'an University, School of Highway, Xi’an, Shaanxi, China
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 December 2022 in Entropy
Verified
Journal Article
Open access
PDF file
Yutong LiuYutong Liu
Yutong Liu
BPBinghong Pan
Binghong Pan
ZZZelong Zhang
Zelong Zhang
RZRanyang Zhang
Ranyang Zhang
Yang ShaoYang Shao
Yang Shao
With the continuous construction of transportation infrastructure, intersection nodes have been increasing rapidly, bringing growing numbers of tunnel- and exit-adjacent sections (TEAS) in mountain expressways in China. With the complex variation in the surrounding environment, drivers always face congestion and confusion on tunnel and the exit connecting sections (TECS) without adequate length, meanwhile excessively long TECS create detours. To better provide a sustainable design strategy for TEAS, based on a certain section of expressway in Shaanxi, China, this paper establishes a theoretical calculation model through analysis. The characteristics of traffic flow and drivers’ light adaptation at tunnel exit are obtained through data collection and driving tests, and the length requirements of the tunnel and exit connecting sections (TECS) are discussed. A VISSIM microscopic simulation model is also built under various design schemes and entropy-based multi-attribute decision making (EBMADM) is used to objectively calculate the weights of the four selected evaluation indexes. Then, the design schemes of the TECS with different lengths have been comprehensively evaluated. The results show the match between the evaluation results of EBMADM with theoretical calculations under existing traffic conditions, which proves the rationality of EBMADM in such problems. For more cases, the results of the EBMADM evaluation show a positive correlation between the length of TECS for the best performing design scheme with traffic volume and diverging ratio.

18 October 2023 in IEEE Access
Verified
Journal Article
Open access
Yutong LiuYutong Liu
Yutong Liu
BPBinghong Pan
Binghong Pan
RSRuihua Song
Ruihua Song
LZLin Zong
Lin Zong
Owing to the challenges faced by two-lane entrance ramps in merging areas on expressways in handling the growing traffic volume, designers are considering implementing three-lane entrance ramps. This approach alleviates capacity bottlenecks and facilitates efficient, safe, and green operations. However, according to the traditional design strategy, the long auxiliary lanes will bring large land occupation and construction consumption, creating obstacles to the reconstruction. To address this issue, this study proposes two new strategies and discusses the applicability of each scheme. A VISSIM microsimulation model was developed and calibrated using the collected data, and five evaluation indicators assessing environmental protection, capacity, traffic efficiency, safety, and construction consumption were selected. This study also presents a comprehensive evaluation(CE) method that combines the CRITIC (Criteria Importance Through Intercriteria Correlation) method and TOPSIS(Technique for Order Preference by Similarity to an Ideal Solution), which considers the association between indicators and offers a more rational evaluation, aiming to recommend optimal designs for various traffic cases. The results indicate that two-lane ramps are still the preferred choice for lower traffic volumes and merging ratios, whereas three-lane ramps demonstrate excellent potential for application under heavy traffic conditions. The CE reveals substantial improvements in optimal designs, with capacity, delay, CO emissions, and conflicts showing maximum enhancements of approximately 20%, 45%, 5%, and 55%, respectively.

13 June 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
QCQiaoliang Chen
Qiaoliang Chen
BPBinghong Pan
Binghong Pan
Yutong LiuYutong Liu
Yutong Liu
Frequent consecutive lane changes and the barrier effect produced by trucks can always contribute to rapid access to the capacity bottleneck at expressway exits, thereby reducing operational performance. This paper proposes to retrofit the conventional interchange design to reduce lane changes and compares them with conventional design and passenger vehicle and truck separation (PVTS) design from multiple fields via VISSIM numerical simulation, which is developed and calibrated with traffic data collected on the eight-lane expressway in China at four levels of service (LOS). Comprehensive evaluation (CE) results reveal that the PVTS strategy improves operational performance by 10–20% at multilane expressway exits, while lane separation around interchanges also yields a similar gain. However, ramps on both the left and right sides show less effective improvement and are even negative at LOS-A and LOS-B. All PVTS and improved designs produce a better comprehensive improvement ratio with a LOS decrease, and improved designs achieve optimal performance below LOS-B with construction cost taken into consideration.

1 January 2026 in Journal of Advanced Transportation
Verified
Journal Article
Open access
PDF file
BLBaoguo Luo
Baoguo Luo
YWYunfei Wang
Yunfei Wang
QYQi Yang
Qi Yang
XCXu Chen
Xu Chen
BPBinghong Pan
Binghong Pan
Yutong LiuYutong Liu
Yutong Liu
Merging‐zone safety remains a critical challenge in transportation engineering due to frequent severe accidents and insufficient research on longitudinal traffic separator (LTS) configurations and the limited availability of evidence‐based guidance for LTS openings in interchange merging areas. This study addresses this gap by developing a physics‐informed computational framework to optimize lane transition zone (LTZ) length and minimum entry clearance distance (MECD). Specifically, (i) UAV videos collected at three Xi’an Ring Expressway interchanges (438 vehicles) are processed using YOLOv5‐based detection to extract vehicle trajectories; (ii) lane‐changing kinematics are characterized using a modified hyperbolic‐tangent trajectory model, and a gap‐acceptance‐based waiting component is incorporated to compute the required lane‐changing and waiting distances for LTZ/MECD design; and (iii) the recommended values are evaluated via controlled simulation experiments across multiple design speeds and lane configurations using delay and conflict‐rate metrics. Through the empirical analysis of 438 vehicles at three Xi’an Ring Expressway interchanges using a UAV and YOLOv5 to extract trajectories, the framework achieves dual safety and efficiency outcomes. It maintains conflict rates below the critical threshold of 0.76 conflicts/veh·km while increasing throughput by 50%–78% in simulated scenarios. The derived design relationships—LTZ ∝ V 2 /C (where V is the design speed and C is the capacity) and MECD = f (V, C, n) (where n is the number of adjacent lanes)—establish quantitative geometric optimization strategies for improving LTS configurations and provide implementable geometric guidance for expressway reconstruction and expansion applications.