The formation of regions corresponding to deformational fragments and dynamically recrystallized grains in the structure of the α-phase after torsion under high hydrostatical pressure at room and...
This reference is dedicated to the problem of time-temperature stability of amorphous (non-crystalline) metal alloys with strongly nonequilibrium structure and unique physical and mechanical properties that are obtained by quenching from the melt at a rate that exceeds one millions of degrees c.o.s. second. As a stability test, the behavior of the plasticity of amorphous alloys is studied. The book examines the fundamental characteristics of amorphous alloys, the basic laws of structural relaxation, generalized information about the phenomenon of the ductile-brittle transition (temper embrittlement), the development of physically justified methods of predicting the stability of the properties, and provides information about the attempts of controlling the structure for the purpose of suppressing or deceleration of the ductile-brittle transition and, as a consequence, increasing the temperature and temporal stability of the amorphous state.
Oxide layers on Mg97Y2Zn1 magnesium alloy with strengthening LPSO-phase were formed by plasma electrolytic oxidation (PEO) in bipolar mode with frequency variation of forming current pulses (50 and 500 Hz) and addition of sodium aluminate or sodium silicate to alkali phosphate fluoride electrolyte. Microstructure, chemical and phase composition, corrosion and mechanical properties of the oxide layers formed were investigated. With increasing current frequency for both electrolytes, an increase in homogeneity of the oxide layers structure and a decrease in their porosity and fracturing at constant thickness were recorded. The oxide layers formed at 500 Hz even with some decrease in hardness have better adhesive strength and 2 orders of magnitude higher short-term corrosion resistance values. PEO of Mg-alloy with LPSO-phase in the electrolyte with addition of sodium aluminate in combination with increased pulse frequency (500 Hz) allows forming the best-quality uniform oxide layer with high hardness, adhesive strength and corrosion resistance properties. The use of electrolyte with addition of sodium silicate reduced the adhesive strength by 1.5 times and brought down the long-term corrosion resistance of oxide layers by an order of magnitude, as compared with the electrolyte with sodium aluminate. The reason for a significant improvement in the complex of protective properties of the oxide layers with an increase in the current pulse frequency is supposed to be a decrease in the power and duration of individual microarc discharges with simultaneous increase in their number per unit oxidized area.
4 November 2019 in Fullerenes, Nanotubes and Carbon Nanostructures
Some experimental evidences and the physics (thermodynamics) of the nanoscale self-intercalation of high-density gaseous molecular hydrogen (ρ ≈ 0.045 g/cm3, T ≈ 300 K) into surface nanoclusters in highly oriented pyrolytic graphite and epitaxial graphene, as well as the nanoscale self-intercalation of high density solid molecular hydrogen (ρ ≈ 0.5 g/cm3, T ≈ 300 K, the compressed pressure ∼ 0.5 Mbar) into graphite nanofibers are considered, with regard to the problem of compact and efficient hydrogen on-board storage and other clean energy applications. Perspectives of further developments of these results are considered, as well.
2 January 2022 in Fullerenes, Nanotubes and Carbon Nanostructures
In this work, data of Rodriguez-Baker et al. and some others were analyzed and interpreted in relation to the long-term, i.e., about 25 years, problem of “super” storage (intercalation) of “reversible” (at 300 K) hydrogen (∼38 ± 10 wt.%, i.e., the atomic ratio (H/C) ≈ 7 ± 3)), along with “irreversible” hydrogen (∼11 ± 3 wt.% ((H/C) ≈ 1.5 ± 0.4)) into graphite nanofibers (GNFs). For a more in-depth study of the a problem, an effective methodology of processing and analyzing the thermal desorption spectra of hydrogen and the related thermogravimetric data was modified and used. It was shown that the above noted extraordinary data on the “super” storage of hydrogen in GNFs are neither an error nor a hoax, as most researchers believed. The necessary conditions were determined to reproduce this extraordinary data. It has also been shown that the Rodriguez-Baker team can reproduce “normal,” i.e., typical results obtained by other researchers on hydrogen storage in GNFs.
This article is devoted to some fundamental aspects of “super” storage in graphite nanofibers (GNF) of “reversible” (~20–30 wt.%) and “irreversible” hydrogen (~7–10 wt.%). Extraordinary results for hydrogen “super” storage were previously published by the group of Rodriguez and Baker at the turn of the century, which been unable to be reproduced or explained in terms of physics by other researchers. For the first time, using an efficient method of processing and analysis of hydrogen thermal desorption spectra, the characteristics of the main desorption peak of “irreversible” hydrogen in GNF were determined: the temperature of the highest desorption rate (Tmax = 914–923 K), the activation energy of the desorption process (Q ≈ 40 kJ mol−1), the pre-exponential rate constant factor (K0 ≈ 2 × 10−1 s−1), and the amount of hydrogen released (~8 wt.%). The physics of hydrogen “super” sorption includes hydrogen diffusion, accompanied by the “reversible” capture of the diffusant by certain sorption “centers”; the hydrogen spillover effect, which provides local atomization of gaseous H2 during GNF hydrogenation; and the Kurdjumov phenomenon on thermoelastic phase equilibrium. It is shown that the above-mentioned extraordinary data on the hydrogen “super” storage in GNFs are neither a mistake nor a mystification, as most researchers believe.