Pretreatment of raw feed water is an essential step for proper functioning of a reverse osmosis (RO) desalination plant as it minimizes the risk of membrane fouling. Conventional pretreatment methods have drawbacks, such as the potential of biofouling, chemical consumption, and carryover. Non-conventional membrane-based pretreatment technologies have emerged as promising alternatives. The present review focuses on recent advances in MF, UF, and NF membrane pretreatment techniques that have been shown to be effective in preventing fouling as well as having low energy consumption. This review also highlights the advantages and disadvantages of polymeric and ceramic membranes. Hybrid technologies, which combine the benefits of conventional and non-conventional methods or different membranes, are also discussed as a potential solution for effective pretreatment. The literature that has been analyzed reveals the challenges associated with RO pretreatment, including the high cost of conventional pretreatment systems, the difficulty of controlling biofouling, and the production of large volumes of wastewater. To address these challenges, sustainable hybrid strategies for ceramic membrane-based systems in RO pretreatment are proposed. These strategies include a thorough assessment of the source water, removal of a wide range of impurities, and a combination of methods such as adsorption and carbon dioxide with a low amount of antiscalants. Furthermore, the suggestion of incorporating renewable energy sources such as solar or wind power can help reduce the environmental impact of the system. A pilot study is also recommended to overcome the difficulties in scaling ceramic systems from laboratory to industrial scale. The review also emphasizes the importance of conducting an effective assessment to suggest a treatment for the brine if needed before being discharged to the environment. By following this framework, sustainable, energy-efficient, and effective solutions can be recommended for pretreatment in desalination systems, which can have significant implications for water scarcity and environmental sustainability.
Increased phosphate concentration in water bodies has led to eutrophication, and its removal is an inevitable requirement of sustainable wastewater purification systems. In this study, MgAl layered doubled hydroxide (LDH) composites doped on the surface of activated carbon (AC/MgAl LDH) with various (Mg + Al) total metal loading (5 wt%, 10 wt%, and 15 wt%) were prepared by the co-precipitation method. The influence of (Mg + Al) total metal loading onto AC was examined to remove phosphate ions from aqueous solutions. The effect of adsorption parameters, including adsorbent dosage, initial solution pH, initial phosphate concentration, contact time, and experiment temperature, were investigated via batch adsorption experiments. The adsorption results demonstrated that the phosphate adsorption capacity significantly improved with increasing the (Mg + Al) metal loading on the surface of AC. The maximum Langmuir phosphate adsorption capacity was 337.2 mg phosphate per gram of AC/MgAl-3 LDH composite (15 wt% Mg + Al) composite at pH ~6.3, 22 °C, and 1 g/L of adsorbent. The kinetic data were best fitted with the pseudo-second order model. The initial solution pH notably influenced the phosphate removal by AC/MgAl-3 LDH composite with a maximum removal at pH 2.3. According to the spent adsorbent characterization results, the dominant mechanisms of phosphate removal by AC/MgAl-3 LDH were electrostatic interactions, ion exchange, and inner-sphere complexation. The phosphate adsorption capacity was gradually increased with increasing the experiment temperature, suggesting an endothermic adsorption process. Overall, the AC/MgAl LDH composites pave the way for an effective strategy for phosphate removal from aqueous solutions.
In this study, a low-cost granular activated carbon doped with Fe2O3 nanoparticles (Fe–GAC) was prepared via a modified sol-gel technique and utilized for the elimination of lead (Pb(II)) and chromium (Cr(T)) ions from synthetic and actual brackish water. The effect of adsorption parameters on the removal of Pb(II) and Cr(T) ions from the water was evaluated in batch adsorption tests. The characterization results validated the distribution of well-defined Fe2O3 nanoparticles onto the GAC surface. GAC loaded with 5 wt.% of Fe2O3 (Fe–GAC 5) exhibited a maximum surface area of 848.2 m2 g−1. The equilibrium data of Cr(T) adsorption were in close agreement with the Langmuir and Sips models with R2 values of 0.95 and 0.96, respectively. However, the R2 values of the equilibrium data for Pb(II) adsorption were greater than 0.91 for all four models, i.e., Langmuir, and Sips, Freundlich and Redlich-Peterson. The maximum Langmuir adsorption capacities of Pb(II) and Cr(T) by Fe–GAC 5 at pH 5.6 and room temperature were 11.9 and 22.1 mg g−1, respectively. Pseudo-second order (R2Pb(II) = 0.99, R2Cr(T) = 0.99) and Elovich kinetic models (R2Pb(II) = 1, R2Cr(T) = 1) were found the most suitable for describing the adsorption kinetics data of Pb(II) and Cr(T) using Fe–GAC 5. The adsorption/desorption studies illustrated that the Fe–GAC is reusable and can be regenerated using 1.0 M HCl. Moreover, the Fe–GAC 5 was found effective to reduce heavy metals loading in actual brackish water to the allowed international standards of drinking water. Accordingly, the Fe–GAC could be a promising material for large-scale applications for the elimination of heavy metals from water.
Oil-contaminated water and industrial oily wastewater discharges have adversely affected aquatic ecosystems and human safety. Membrane separation technology offers a promising solution for effective oil–water separation. Thus, a membrane with high surface area, hydrophilic–oleophobic properties, and stability is a promising candidate. Electrospinning, a straightforward and efficient process, produces highly porous polymer-based membranes with a vast surface area and stability. The main objective of this study is to produce hydrophilic–oleophobic polyacrylonitrile (PAN) and cellulose acetate (CA) nanofibers using core–shell electrospinning. Incorporating CA into the shell of the nanofibers enhances the wettability. The core PAN polymer improves the electrospinning process and contributes to the hydrophilicity–oleophobicity of the produced nanofibers. The PAN/CA nanofibers were characterized by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, X-ray diffraction, and surface-wetting behavior. The resulting PAN/cellulose nanofibers exhibited significantly improved surface-wetting properties, demonstrating super-hydrophilicity and underwater superoleophobicity, making them a promising choice for oil–water separation. Various oils, including gasoline, diesel, toluene, xylene, and benzene, were employed in the preparation of oil–water mixture solutions. The utilization of PAN/CA nanofibers as a substrate proved to be highly efficient, confirming exceptional separation efficiency, remarkable stability, and prolonged durability. The current work introduces an innovative single-step fabrication method of composite nanofibers, specially designed for efficient oil–water separation. This technology exhibits significant promise for deployment in challenging situations, offering excellent reusability and a remarkable separation efficiency of nearly 99.9%.
About Me
Abdelrahman K A Khalil is a research assistant in the Water Desalination Research Group at the University of Sharjah
Abdelrahman K A Khalil is a research assistant in the Water Desalination Research Group at the University of Sharjah