Artem Borisov

Mr. Artem Borisov

Peter the Great St. Petersburg Polytechnic University, Saint Petersburg, Sankt-Peterburg, Russia
orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 July 2023 in Metals
Verified
Journal Article
Open access
PDF file
Vadim SufiiarovVadim Sufiiarov
Vadim Sufiiarov
ABArtem Borisov
Artem Borisov
APAnatoly Popovich
Anatoly Popovich
DEDanil Erutin
Danil Erutin
In this paper, the effect of TiC particle size on the microstructure and mechanical properties of an Inconel 718/TiC composite material fabricated using binder jetting additive manufacturing was investigated. Vacuum sintering, hot isostatic pressing and heat treatment as post-processing were applied to the samples. The addition of 1 wt% micron-sized TiC to the Inconel 718 matrix resulted in a significant increase in strength and relative elongation during tensile tests at both room temperature and 700 °C. The distribution of micron-sized TiC particles in the matrix was uniform, and the MC phase precipitated after HT was located along the grain boundaries and near the micron-sized TiC particles, which contributed to the strengthening. The hardness increased insignificantly with the addition of micron-sized TiC. The nano-sized TiC particles added to the matrix were located on the surfaces of the Inconel 718 particles of the initial powders, which obstructed sintering and resulted in a porous structure and, consequently, low mechanical properties.

16 October 2024 in Materials
Verified
Journal Article
Open access
PDF file
ABArtem Borisov
Artem Borisov
ASAleksey Shamshurin
Aleksey Shamshurin
MKMark Kovalev
Mark Kovalev
APAnatoliy Popovich
Anatoliy Popovich
Vadim SufiiarovVadim Sufiiarov
Vadim Sufiiarov
This paper investigated the influence of titanium carbide (TiC) content on the processing, microstructure, mechanical and tribological properties of Inconel 718/TiC composites produced by binder jetting additive manufacturing. It was found that increasing the amount of TiC required an increase of the drying intensity during printing due to a decrease in the thermal conductivity of the powder mixture. The sintering process also depended on the TiC content. The most optimal modes were 1270 °C for 10 h for samples with 0 and 3% TiC and 1280 °C for 5 h for samples with 5 and 10% TiC. The hardness of the materials increased as the proportion of reinforcement increased. The best tensile properties, also at high temperatures, were possessed by samples with 3% TiC, showing high strength and, in addition, satisfactory plasticity. The maximum wear resistance was achieved by the composite material containing 5% TiC.

11 September 2025 in Materials Science in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
ABArtem Borisov
Artem Borisov
MZMaria Zaitceva
Maria Zaitceva
APAnatoliy Popovich
Anatoliy Popovich
VSVadim Sufiiarov
Vadim Sufiiarov
Binders play a key role in binder jetting additive manufacturing (BJAM), determining the stability of the printing process, geometric accuracy, and properties of the final parts. Analysis of recent research and developments indicates that binders are usually based on water, solvents, or their mixtures in various ratios, with all three types having almost equal significance depending on the specific application. Special emphasis is placed on the rheological characteristics of binders, which determine their printability, as well as on post-processing, which affects the phase composition of the resulting products. The review proposes a classification of binders for BJAM, categorizing them into four types: Liquid organic binders, solid binders, nanoparticle-filled binders, and reactive binders. The evolution of research interest in different binder types over the past 15 years is analyzed, revealing key trends and shifts in scientific focus. Perspectives for future studies are outlined, emphasizing the need for tailored binder development. The advancement of BJAM and the expansion of its applications are directly dependent on research aimed at creating new binder systems that meet the growing demands of the industry. An integrated approach, combining chemical synthesis and materials science analysis, opens up prospects for the development of specialized formulations tailored to specific materials and functional requirements.

1 April 2026 in Protection of Metals and Physical Chemistry of Surfaces
Verified
Journal Article
Closed access
PDF file
ABArtem Borisov
Artem Borisov
MBM. Ya. Borisova
M. Ya. Borisova
APA. A. Popovich
A. A. Popovich
VSV. Sh. Sufiiarov
V. Sh. Sufiiarov
Binders play a crucial role in binder jetting, as they determine printing process stability, geometric accuracy, and the properties of the final products. Analysis of modern research shows that the basis of binders is usually water, organic solvents or their mixtures in various proportions, and all three types are of almost equal importance depending on the specific application. Particular attention is paid to the rheological characteristics of binders, which determine the printability, as well as the binder removal process, which affects the phase composition of the resulting products. This review proposes a classification of binders for binder jetting, categorizing them into four types: liquid organic, solid, nanoparticle-filled, and reactive. Further development of binder jetting technology and expansion of its industrial application directly depend on research aimed at creating new binder systems that meet growing industrial requirements. An integrated approach combining chemical synthesis and materials science analysis opens up prospects for the development of specialized formulations adapted to specific classes of materials and functional requirements.