The iron and steel industry remains one of the most energy-intensive activities with high CO2 emissions. Generally, the use of fossil coal as chemical energy in an electric arc furnace (EAF) makes up 40–70% of the total direct emissions in this steelmaking process. Therefore, substituting conventional fossil fuels with alternatives is an attractive option for reducing CO2 emissions. In this study, the environmental impacts of EAF-produced steel were comprehensively assessed using pulverized hydrochar as the charged and injected material as a replacement for fossil coal. An environmental analysis was performed based on the LCA methodology according to the framework of ISO 14044. This study evaluated two different outlines: the use of fossil coal and its replacement with hydrochar from the winemaking industry as a carbon source in the EAF steelmaking process. The environmental impacts from the manufacturing of the hydrochar were calculated using different scenarios, including novel industrial ways to use vinasse as a moisture source for the co-hydrothermal carbonization of vine pruning and exhausted grape marc (EGM). The environmental impacts per unit of steel were reported as a function of the ratio between the fixed carbon of the injected material and the material amount itself. The results highlight the sustainability of the hydrothermal carbonization process and the use of the hydrochar in EAF steelmaking. Moreover, the electricity mix used for the EAF process has significant relevance. The main outline of the results might assist decision-makers to determine which technological route is most likely to be effective in reducing future CO2 emissions from the iron and steel industry.
This study explores the hydrothermal carbonization (HTC) process applied to the exhausted chestnut produced by the tannin extraction industry, utilizing process water recirculation to enhance the efficiency and sustainability of the conversion process. Tannin extraction from wood typically involves hot water treatment, leaving behind residual wood biomass known as exhausted wood. These by-products maintain their renewable properties because they have only been exposed to hot water under a high pressure, which is unlikely to cause major alterations in their structural components. Hydrothermal treatment was carried out at temperatures of 220 °C and 270 °C for 1 h, with process water being recirculated four times. This investigation focused on analyzing the effects of recirculation on the yield and fuel properties of hydrochar, as well as characterizing the combustion behavior of the obtained hydrochar. The results indicated that recirculation of process water led to improvements in both the mass and energy yields of hydrochar. The mass yield of the hydrochar samples increased by 5–6%, and the ERE of the hydrochar samples increased by 5–8% compared to the HTC reference sample. However, alterations in the combustion characteristics were observed, including decreases in ignition temperature and combustion reactivity. The results indicate that, with PW recirculations, the combustion index decreased by about 14% and 18% for 220 °C and 270 °C, respectively. Overall, this research demonstrates the potential of utilizing HTC on chestnut tannin residue with process water recirculation to produce stable solid fuel and provides insights into the combustion behavior of the resulting hydrochar.
The valorisation of lignocellulosic residues into bio-based feedstocks is a key strategy for advancing circular bioeconomy models. In this study, chestnut wood residues, including virgin wood (VW) and detannized wood (DT) from the tannin industry, were evaluated as substrates for polyhydroxyalkanoate (PHA) production using Cupriavidus necator. Biomass was subjected to thermo-acid hydrolysis followed by ion-exchange detoxification, yielding hydrolysates rich in organic acids (levulinic, acetic, and formic acids) and residual inhibitory compounds. Both substrates supported microbial growth and PHA accumulation, although clear differences in performance were observed. The maximum biomass concentration reached 1.26 ± 0.01 g L−1 in VW hydrolysate and 0.40 ± 0.03 g L−1 in DT hydrolysate. PHA production was higher in VW hydrolysate, reaching 68.51 mg L−1 with 5.44% (w/w) accumulation, while DT hydrolysate yielded 0.21 mg L−1 with 6.01% (w/w). The reduced biomass formation in DT hydrolysate was associated with the greater persistence of inhibitory compounds generated during thermo-acid treatment. Although the obtained PHA yields are lower than those reported for optimized lignocellulosic systems, this study demonstrates for the first time the feasibility of producing PHA from chestnut wood residues, including industrial detannized byproducts, without nutrient supplementation. These findings highlight the potential of tannin-industry waste streams as alternative feedstocks for biopolymer production, while indicating that optimization of hydrolysis conditions, detoxification efficiency, and fermentation strategy is required to improve process performance.