Ahmed Merzoug

Mr. Ahmed Merzoug

Petroleum and Geosystem Engineering, University of Texas at Austin, Austin, Texas, USA
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 September 2023 in Geoenergy Science and Engineering
Verified
Journal Article
Closed access
CWChenyu Wu
Chenyu Wu
AMAhmed Merzoug
Ahmed Merzoug
Xincheng WanXincheng Wan
Xincheng Wan
KLKegang Ling
Kegang Ling
JZJin Zhao
Jin Zhao
LJLu Jin
Lu Jin

25 February 2025 in Mathematical Geosciences
Verified
Journal Article
Closed access
PDF file
AMAhmed Merzoug
Ahmed Merzoug
MPMichael Pyrcz
Michael Pyrcz

23 July 2025 in Mathematical Geosciences
Verified
Journal Article
Closed access
PDF file
AMAhmed Merzoug
Ahmed Merzoug
LLLei Liu
Lei Liu
MPMichael J. Pyrcz
Michael J. Pyrcz

9 January 2023 in Applied Mechanics
Verified
Journal Article
Open access
PDF file
AMAhmed Merzoug
Ahmed Merzoug
AEAbdulaziz Ellafi
Abdulaziz Ellafi
Vamegh RasouliVamegh Rasouli
Vamegh Rasouli
Hadi JabbariHadi Jabbari
Hadi Jabbari
Correct estimation of hydraulic fracture height growth is a critical step in the design of Hydraulic Fracturing (HF) treatment, as it maximizes the reservoir stimulation and returns on investment. The height of the fractures is governed by several in situ conditions, especially stress variation with depth. The common workflow to estimate stress is by building the mechanical earth model (MEM) and calibrating it using the Diagnostic Fracture Injection Test (DFIT). However, DFIT interpretation is a complex task, and depending on the method used, different results may be obtained that will consequently affect the predicted hydraulic fracture height. This work used the tangent and compliance methods for DFIT interpretation, along with isotropic and anisotropic stress profiles, to estimate the HF height growth using numerical modeling in a 3D planar HF simulator. Data from two wells in the Anadarko Basin were used in this study. The predicted height was compared with microseismic data. The results showed that even though the tangent method fits better to the isotropic stress profile, HF did not match with the microseismic data. On the contrary, the anisotropic stress profile showed a good match between the compliance DFIT model and the microseismic events. Based on the discussions presented in this study, the validity of the DFIT interpretation is debatable, and when the formations are anisotropic, the isotropic model fails to correctly estimate the minimum stress profile, which is the main input for the estimation of the fracture height. This is in addition to the fact that some researchers have questioned the use of the tangent method in low-permeability formations.

23 April 2023 in Eng
Verified
Journal Article
Open access
PDF file
AMAhmed Merzoug
Ahmed Merzoug
VRVamegh Rasouli
Vamegh Rasouli
Fracture-driven interaction FDI (colloquially called “Frac-hit”) is the interference of fractures between two or more wells. This interference can have a significant impact on well production, depending on the unconventional play of interest (which can be positive or negative). In this work, the surrogate model was used along with metaheuristic optimization algorithms to optimize the completion design for a case study in the Bakken. A numerical model was built in a physics-based simulator that combines hydraulic fracturing, geomechanics, and reservoir numerical modeling as a continuous simulation. The stress was estimated using the anisotropic extended Eaton method. The fractures were calibrated using Microseismic Depletion Delineation (MDD) and microseismic events. The reservoir model was calibrated to 10 years of production data and bottom hole pressure by adjusting relative permeability curves. The stress changes due to depletion were calibrated using recorded pressure data from MDD and FDI. Once the model was calibrated, sensitivity analysis was run on the injected volumes, the number of clusters, the spacing between clusters, and the spacing between wells using Sobol and Latin Hypercube sampling. The results were used to build a surrogate model using an artificial neural network. The coefficient of correlation was in the order of 0.96 for both training and testing. The surrogate model was used to construct a net present value model for the whole system, which was then optimized using the Grey Wolf algorithm and the Particle Swarm Optimization algorithm, and the optimum design was reported. The optimum design is a combination of wider well spacing (1320 ft), tighter cluster spacing (22 ft), high injection volume (1950 STB/cluster), and a low cluster number per stage (seven clusters). This study suggests an optimum design for a horizontal well in the Bakken drilled next to a well that has been producing for ten years. The design can be deployed in new wells that are drilled next to depleted wells to optimize the system’s oil production.

1 September 2023 in Petroleum
Verified
Journal Article
Open access
AMAhmed Merzoug
Ahmed Merzoug
VPVibhas Pandey
Vibhas Pandey
VRVamegh Rasouli
Vamegh Rasouli
BDBranko Damjanac
Branko Damjanac
HPHui Pu
Hui Pu