We propose and demonstrate a tunable single frequency fiber laser based on Fabry Pérot laser diode (FP-LD) injection locking. The single frequency operation principle is based on the fact that the output from a FP-LD injection locked by a multi-longitudinal-mode (MLM) light can have fewer longitudinal-modes number and narrower linewidth. By inserting a FP-LD in a fiber ring laser cavity, single frequency operation can be possibly achieved when stable laser oscillation established after many roundtrips through the FP-LD. Wavelength switchable single frequency lasing can be achieved by adjusting the tunable optical filter (TOF) in the cavity to coincide with different mode of the FP-LD. By adjustment of the drive current of the FP-LD, the lasing modes would shift and wavelength tunable operation can be obtained. In experiment, a wavelength tunable range of 32.4 nm has been obtained by adjustment of the drive current of the FP-LD and a tunable filter in the ring cavity. Each wavelength has a side-mode suppression ratio (SMSR) of at least 41 dB and a linewidth of about 13 kHz.

In this paper, we propose and demonstrate a technique to realize multiwavelength operation in erbium-doped fiber lasers (EDFLs) by inserting two Fabry Pérot laser diodes (FP-LDs) in the laser cavity respectively in cascaded and parallel way. The FP-LDs not only act as wavelength selection elements, but also offer optical gain or loss for the operation wavelengths in the laser cavity. The gains or losses for the oscillation wavelengths obtained from FP-LDs differ with adjustment of the driving current of the FP-LDs. Thus, the utilization of the FP-LDs in the laser cavity can introduce wavelength dependent gain or loss which can effectively suppress the competition caused by the homogeneous gain broadening of the erbium-doped fiber (EDF). As a result, 16-wavelength and 20-wavelength operation with a wavelength-spacing of 1.25 nm has been achieved respectively in the cascaded and parallel FP-LDs based EDFL schemes. The measured power fluctuation of each wavelength is smaller than 0.4dB for both EDFLs. Furthermore, the injection locking of the FP-LDs ensures a narrow linewidth of the EDFL output and the linewidth is estimated to be narrower than 100 MHz for the cascaded scheme based EDFL.

Far-field high-density optics storage and readout involve the interaction of a sub-100 nm beam profile laser to store and retrieve data with nanostructure media. Hence, understanding the light–matter interaction responding in the far-field in such a small scale is essential for effective optical information processing. We present a theoretical analysis and an experimental study for far-field and non-intrusive optical mapping of nanostructures. By a comprehensive analytical derivation for interaction between the modulated light and the target in a confocal laser scanning microscopy (CLSM) configuration, it is found that the CLSM probes the local density of states (LDOSs) in the far field rather than the sample geometric morphology. With a radially polarized (RP) light for illumination, the far-field mapping of LDOS at the optical resolution down to 74 nm is obtained. In addition, it is experimentally verified that the target morphology is mapped only when the far-field mapping of LDOS coincides with the geometric morphology, while light may be blocked from entering the nanostructures medium with weak or missing LDOS, hence invalidating high-density optical information storage and retrieval. In this scenario, nanosphere gaps as small as 33 nm are clearly observed. We further discuss the characterization for far-field and non-intrusive interaction with nanostructures of different geometric morphology and compare them with those obtainable with the projection of near-field LDOS and scanning electronic microscopic results.

Autostereoscopy is usually perceived at finite viewpoints that result from the separated pixel array of a display system. With directionally illuminated autostereoscopy, the separation of the illumination channel from the image channel provides extra flexibility in optimizing the performance of autostereoscopy. This work demonstrates that by taking advantage of illumination freedom, seamless viewpoints in the sweet viewing region, where the ghosting does not cause significant discomfort, are realized. This realization is based on illuminating the screen with a polyline array of light emitting diodes (LEDs), and continuous viewpoints are generated through independent variation in the radiance of each individual LED column. This new method is implemented in the directionally illuminated display for both single and multiple viewers, proving its effectiveness as a valuable technique for achieving a high-quality and high-resolution autostereoscopic display with seamless viewpoints.