The end effector is a major part of a robot system and it defines the task the robot can perform. However, typically, a gripper is suited to grasping only a single or relatively small number of different objects. Dexterous grippers offer greater grasping ability but they are often very expensive, difficult to control and are insufficiently robust for industrial operation. This paper explores the principles of soft robotics and the design of low-cost grippers able to grasp a broad range of objects without the need for complex control schemes. Two different soft end effectors have been designed and built and their physical structure, characteristics, and operational performances have been analyzed. The soft grippers deform and conform to the object being grasped, meaning they are simple to control and minimal grasp planning is required. The soft nature of the grippers also makes them better suited to handling fragile and delicate objects than a traditional rigid gripper.
To clarify the advantages of using soft robots in all aspects of life, the effective behaviour of the pneumatic muscle actuator (PMA) must be known. In this work, the performances of the PMA are explained and modelled with three formulas. The first formula describes the pulling force of the actuator based on the structure parameters; furthermore, the formula presented is the generalised contraction force for wholly-pneumatic muscle actuators. The second important model is the length formula, which is modified to our previous work to fit different actuator structures. Based on these two models, the stiffness of the actuator is formulated to illustrate its variability at different air pressure amounts. In addition, these formulas will make the selection of proper actuators for any robot arm structure easier using the knowledge gained from their performance. On the other hand, the desired behaviour of this type of actuator will be predefined and controlled.
Rehabilitation interventions play a vital role especially in most post-stroke care. Many rehabilitation robotic devices have been designed and developed to assist many individuals suffering from stroke or similar disabling illness and living with reduced mobility of the arms, hands and other joint. However, these devices remain unmanageable to use by the patients alone not only because they are cumbersome to use but also due to their weights, fix and non-portable characteristics, and so on. Here for elbow joint rehabilitation, we investigate and propose a novel exoskeleton soft robotic arm, which is wearable, lightweight and portable so that it would allow patients to perform repetitive motion therapy more often with a greater intensity in their homes and relevant to their daily activities. The proposed arm consists of various novel pneumatic Muscle Actuators (pMA) capable of bending in contrary to traditional pMA. Analysis, design, integration and characterisation of the proposed arm are presented and geometrical and numerical models are obtained. Various experiments revealed its behaviour and the relationship among pressure, length, force, and bending angle in different setups such as isotonic and isometric. The nonlinear, time varying and intractable dynamic of the constructed prototype demanded the design and development of an appropriate closed loop controller for adhering to target rehabilitation profiles. As proof of the concept a Model Reference Adaptive Control (MRAC) was designed and results were presented. By achieving design objectives, this study shows that the proposed portable exoskeleton has the ability to offer more effective intense rehabilitation therapies at home without the need to therapists and with a lower cost.
This article presents a novel design for a double bend pneumatic muscle actuator (DB-PMA) inspired by snake lateral undulation. The presented actuator has the ability to bend in opposite directions from its two halves. This behavior results in horizontal and vertical movements of the actuator distal ends. The kinematics for the proposed actuator are illustrated and experiments conducted to validate its unique features. Furthermore, a continuum robot arm with the ability to move in parallel (horizontal displacement) is designed with a single DB-PMA and a two-finger soft gripper. The performance of the soft robot arm presented is explained, then another design of the horizontal motion continuum robot arm is proposed, using two self-bending contraction actuators (SBCA) in series to overcome the payload effects on the upper half of the soft arm.
Modelling of pneumatic muscle actuators “PMA” is one of the valued challenges in soft robotic researches, which is still under modification for the McKibben artificial muscle. Accurate force, length and position models allow for the wide use of make the continuum robot arm in industrial and medical applications. Moreover, accurate control can be achieved. This paper presents new formulas to model the length of contraction PMA. The sigmoidal shape of contraction length characteristics makes the sigmoid function a suitable form to model, which its coefficients depend on the nominal length “Lo”. Furthermore, we modified the existing force model by calculating the most affected parameters. Then we are modelling the angle of the arm. The three proposed models make it easy to track the length (position), the force of PAMs and position angle of PMA arm.
This article presents a novel design of a continuum arm, which has the ability to extend and bend efficiently. Numerous designs and experiments have been done to different dimensions on both types of McKibben pneumatic muscle actuators (PMA) in order to study their performances. The contraction and extension behaviour have been illustrated with single contractor actuators and single extensor actuators, respectively. The tensile force for the contractor actuator and the compressive force for the extensor PMA are thoroughly explained and compared. Furthermore, the bending behaviour has been explained for a single extensor PMA, multi extensor actuators and multi contractor actuators. A two-section continuum arm has been implemented from both types of actuators to achieve multiple operations. Then, a novel construction is proposed to achieve efficient bending behaviour of a single contraction PMA. This novel design of a bending-actuator has been used to modify the presented continuum arm. Two different position control strategies are presented, arising from the results of the modified soft robot arm experiment. A cascaded position control is applied to control the position of the end effector of the soft arm at no load by efficiently controlling the pressure of all the actuators in the continuum arm. A new algorithm is then proposed by distributing the x, y and z-axis to the actuators and applying an effective closed-loop position control to the proposed arm at different load conditions.