Therapeutic options for the highly pathogenic human severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) causing the current pandemic coronavirus disease (COVID-19) are urgently needed. COVID-19 is associated with viral pneumonia and acute respiratory distress syndrome causing significant morbidity and mortality. The proposed treatments for COVID-19 have shown little or no effect in the clinic so far. Additionally, bacterial and fungal pathogens contribute to the SARS-CoV-2-mediated pneumonia disease complex. The antibiotic resistance in pneumonia treatment is increasing at an alarming rate. Therefore, carbon-based nanomaterials (CBNs), such as fullerene, carbon dots, graphene, and their derivatives constitute a promising alternative due to their wide-spectrum antimicrobial activity, biocompatibility, biodegradability, and capacity to induce tissue regeneration. Furthermore, the antimicrobial mode of action is mainly physical (e.g., membrane distortion), characterized by a low risk of antimicrobial resistance. In this Review, we evaluated the literature on the antiviral activity and broad-spectrum antimicrobial properties of CBNs. CBNs had antiviral activity against 13 enveloped positive-sense single-stranded RNA viruses, including SARS-CoV-2. CBNs with low or no toxicity to humans are promising therapeutics against the COVID-19 pneumonia complex with other viruses, bacteria, and fungi, including those that are multidrug-resistant.

Face masks have globally been accepted to be an effective protective tool to prevent bacterial and viral transmission, especially against indoor aerosol transmission. However, commercial face masks contain filters that are made of materials that are not capable of inactivating either SARS-CoV-2 or multidrug-resistant bacteria. Therefore, symptomatic and asymptomatic individuals can infect other people even if they wear them because some viable viral or bacterial loads can escape from the masks. Furthermore, viral or bacterial contact transmission can occur after touching the mask, which constitutes an increasing source of contaminated biological waste. Additionally, bacterial pathogens contribute to the SARS-CoV-2-mediated pneumonia disease complex, and their resistance to antibiotics in pneumonia treatment is increasing at an alarming rate. In this regard, herein, we report the development of a non-woven face mask filter fabricated with a biofunctional coating of benzalkonium chloride that is capable of inactivating more than 99% of SARS-CoV-2 particles in one minute of contact, and the life-threatening methicillin-resistant Staphylococcus aureus and Staphylococcus epidermidis (normalized antibacterial halos of 0.52 ± 0.04 and 0.72 ± 0.04, respectively). Nonetheless, despite the results obtained, further studies are needed to ensure the safety and correct use of this technology for the mass production and commercialization of this broad-spectrum antimicrobial face mask filter. Our novel protective non-woven face mask filter would be useful for many healthcare workers and researchers working in this urgent and challenging field.

Alginate is a highly promising biopolymer due to its non-toxic and biodegradable properties. Alginate hydrogels are often fabricated by cross-linking sodium alginate with calcium cations and can be engineered with highly desirable enhanced physical and biological properties for biomedical applications. This study reports on the anticancer, antiviral, antibacterial, in vitro, and in vivo toxicity, water absorption, and compound release properties of an alginate hydrogel crosslinked with calcium and different amounts of zinc cations. The results showed that the calcium alginate hydrogel film crosslinked with the highest amount of zinc showed similar water sorption properties to those of calcium alginate and released a suitable amount of zinc to provide anticancer activity against melanoma and colon cancer cells and has antibacterial properties against methicillin-resistant Staphylococcus epidermidis and antiviral activity against enveloped and non-enveloped viruses. This film is non-toxic in both in vitro in keratinocyte HaCaT cells and in vivo in the Caenorhabditis elegans model, which renders it especially promising for biomedical applications.

Infection prevention clothing is becoming an essential protective tool in the current pandemic, especially because now we know that severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) can easily infect humans in poorly ventilated indoor spaces. However, commercial infection prevention clothing is made of fabrics that are not capable of inactivating the virus. Therefore, viral infections of symptomatic and asymptomatic individuals wearing protective clothing such as masks can occur through aerosol transmission or by contact with the contaminated surfaces of the masks, which are suspected as an increasing source of highly infectious biological waste. Herein, we report an easy fabrication method of a novel antiviral non-woven fabric containing polymer filaments that were coated with solidified hand soap. This extra protective fabric is capable of inactivating enveloped viruses such as SARS-CoV-2 and phage Φ6 within 1 min of contact. In this study, this antiviral fabric was used to fabricate an antiviral face mask and did not show any cytotoxic effect in human keratinocyte HaCaT cells. Furthermore, this antiviral non-woven fabric could be used for the fabrication of other infection prevention clothing such as caps, scrubs, shirts, trousers, disposable gowns, overalls, hoods, aprons, and shoe covers. Therefore, this low-cost technology could provide a wide range of infection-protective tools to combat COVID-19 and future pandemics in developed and underdeveloped countries.

Purpose: The COVID-19 pandemic emphasises the need for antiviral materials that can reduce airborne and surface-based virus transmission. This study aims to propose the use of additive manufacturing (AM) and surrogate modelling for the rapid development and deployment of novel copper-tungsten-silver (Cu-W-Ag) microporous architecture that shows strong antiviral behaviour against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Design/methodology/approach: The research combines selective laser melting (SLM), in-situ alloying and surrogate modelling to conceive the antiviral Cu-W-Ag architecture. The approach is shown to be suitable for redistributed manufacturing by representing the pore morphology through a surrogate model that parametrically manipulates the SLM process parameters: hatch distance (h_d), scan speed (S_s) and laser power (L_p). The method drastically simplifies the three-dimensional (3D) printing of microporous materials by requiring only global geometrical dimensions solving current bottlenecks associated with high computed aided design data transfer required for the AM of porous materials. Findings: The surrogate model developed in this study achieved an optimum parametric combination that resulted in microporous Cu-W-Ag with average pore sizes of 80 µm. Subsequent antiviral evaluation of the optimum architecture showed 100% viral inactivation within 5 h against a biosafe enveloped ribonucleic acid viral model of SARS-CoV-2. Research limitations/implications: The Cu-W-Ag architecture is suitable for redistributed manufacturing and can help reduce surface contamination of SARS-CoV-2. Nevertheless, further optimisation may improve the virus inactivation time. Practical implications: The study was extended to demonstrate an open-source 3D printed Cu-W-Ag antiviral mask filter prototype. Social implications: The evolving nature of the COVID-19 pandemic brings new and unpredictable challenges where redistributed manufacturing of 3D printed antiviral materials can achieve rapid solutions. Originality/value: The papers present for the first time a methodology to digitally conceive and print-on-demand a novel Cu-W-Ag alloy that shows high antiviral behaviour against SARS-CoV-2.