Aleksandra Mirowska

Dr. Aleksandra Mirowska

Gdańsk University of Technology, Faculty of Mechanical Engineering
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 May 2024 in International Journal of Hydrogen Energy
Verified
Journal Article
Open access
BSBehzad Sadeghi
Behzad Sadeghi
Pasquale CavalierePasquale Cavaliere
Pasquale Cavaliere
MBMUTLUCAN BAYAT
MUTLUCAN BAYAT
NENiloofar Ebrahimzadeh Esfahani
Niloofar Ebrahimzadeh Esfahani
Aleksandra MirowskaAleksandra Mirowska
Aleksandra Mirowska
DKDamian Koszelow
Damian Koszelow

31 August 2023 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
Aleksandra MirowskaAleksandra Mirowska
Aleksandra Mirowska
BSBehzad Sadeghi
Behzad Sadeghi
BSBehzad Sadeghian
Behzad Sadeghian
ATAboozar Taherizadeh
Aboozar Taherizadeh
MSMarek Szkodo
Marek Szkodo
PCPasquale Cavaliere
Pasquale Cavaliere
The friction stir welding process was simulated for joining AA6082 aluminum alloy with the use of the computational fluid dynamics method. Two different tool geometries were used—a tapered cylindrical pin (simple pin) and a hexagonal pin with grooves (complex pin). The analysis of the simulations performed was discussed in terms of temperature evolution during the process, total heat input, residual stresses and material flow. Simulations revealed that a 5% higher temperature, equal to maximum 406 °C, was provided when using the complex pin than with the simple pin. Higher temperature and higher shear stresses during the welding with the complex pin caused the introduction of higher residual stresses in the weld. Experimental results on the produced welds allowed observation of the microstructure of the joints, hardness tests in cross sections and tensile strength tests. Due to the higher temperature during the process with the complex pin and the more efficient recrystallization process, grain refinement in the SZ was more pronounced. The average grain size in the stir zone for the weld produced with the complex pin was equal to 11 ± 1 µm, and in the case of the simple pin 14 ± 1 µm. The presented hardness profiles revealed that the weld produced with a complex pin had higher hardness in the stir zone, equal to 89.5 ± 1.3 HV, which is consistent with the Hall-Petch relationship. The obtained UTS values corresponded to the joint efficiency of 72.5 ± 4.9% and 55.8 ± 8.6% for the weld produced with the complex pin and the simple pin.

11 November 2023 in International Journal of Hydrogen Energy
Verified
Journal Article
Open access
Pasquale CavalierePasquale Cavaliere
Pasquale Cavaliere
APAngelo Perrone
Angelo Perrone
LDLeandro Dijon
Leandro Dijon
Aleksandra MirowskaAleksandra Mirowska
Aleksandra Mirowska
DKDamian Koszelow
Damian Koszelow

1 September 2023 in International Journal of Hydrogen Energy
Verified
Journal Article
Open access
Pasquale CavalierePasquale Cavaliere
Pasquale Cavaliere
LDLeandro Dijon
Leandro Dijon
Aleksandra MirowskaAleksandra Mirowska
Aleksandra Mirowska
DKDamian Koszelow
Damian Koszelow

24 May 2024 in Minerals Engineering
Verified
Journal Article
Open access
Pasquale CavalierePasquale Cavaliere
Pasquale Cavaliere
Behzad SadeghiBehzad Sadeghi
Behzad Sadeghi
LDLeandro Dijon
Leandro Dijon
Aleksandra MirowskaAleksandra Mirowska
Aleksandra Mirowska
DKDamian Koszelow
Damian Koszelow

3 November 2020 in Materials
Verified
Journal Article
Open access
PDF file
Aleksandra MirowskaAleksandra Mirowska
Aleksandra Mirowska
Marek SzkodoMarek Szkodo
Marek Szkodo
The modern and eco-friendly friction stir welding (FSW) method allows the combination of even such materials that are considered to be non-weldable. The development of FSW technology in recent years has allowed a rapid increase in the understanding of the mechanism of this process and made it possible to perform the first welding trials of modern polymeric and composite materials, the joining of which was previously a challenge. The following review work focuses on presenting the current state of the art on applying this method to particular groups of materials. The paper has been divided into subchapters focusing on the most frequently used construction materials, with particular emphasis on their properties, applications, and usage of the FSW method for these materials. Mechanisms of joint creation are discussed, and the microstructure of joints and the influence of material characteristics on the welding process are described. The biggest problems observed during FSW of these materials and potential causes of their occurrence are quoted. The influence of particular parameters on the properties of manufactured joints for each group of materials is discussed on the basis of a wide literature review.