In this article, simplified and easy-to-work-with equations for the Lambert W-function are derived. This function is widely used to solve equations related to photovoltaic systems. More specifically, this mathematical function represents a useful tool when modeling solar cells/panels performance (that is, the current-voltage curve) by analytical approaches. However, the Lambert W-function has a complex solving process which might represent an unaffordable mathematical challenge for a great number of professionals/technicians in the photovoltaic industrial sector. Simple approximations for the Lambert W-function on both of its branches (positive and negative) are proposed in this article. The results of the present article show a simple but accurate way for photovoltaic systems modeling, even when these systems comprise a maximum power point tracking subsystem.
In this paper, we propose very simple analytical methodologies for modeling the behavior of photovoltaic (solar cells/panels) using a one-diode/two-resistor (1-D/2-R) equivalent circuit. A value of a = 1 for the ideality factor is shown to be very reasonable for the different photovoltaic technologies studied here. The solutions to the analytical equations of this model are simplified using easy mathematical expressions defined for the Lambert W-function. The definition of these mathematical expressions was based on a large dataset related to solar cells and panels obtained from the available academic literature. These simplified approaches were successfully used to extract the parameters from explicit methods for analyzing the behavior of solar cells/panels, where the exact solutions depend on the Lambert W-function. Finally, a case study was carried out that consisted of fitting the aforementioned models to the behavior (that is, the I-V curve) of two solar panels from the UPMSat-1 satellite. The results show a fairly high level of accuracy for the proposed methodologies.
This paper shows wind speed measurements from the TASEC-Lab experiment in a stratospheric balloon mission. The mission was launched in July 2021 from León (Spain) aerodrome. Measurements of horizontal wind speed in relation to the balloon gondola were successfully carried out with a cup anemometer. According to the available literature, this is the first time a cup anemometer has been used in a stratospheric balloon mission. The results indicate the need to consider the horizontal wind speed from the balloon ascent phase for thermal calculations of the mission.
This paper presents the development of the UPMSat-2 sun sensor, from the design to on-orbit operation. It also includes the testing of the instrument, one of the most important tasks that needs to be performed to operate a sensor with precision. The UPMSat-2 solar sensor has been designed, tested, and manufactured at the Universidad Politécnica de Madrid (UPM) using 3D printing and COTS (photodiodes). The work described in this paper was carried out by students and teachers of the Master in Space Systems (Máster Universitario en Sistemas Espaciales—MUSE). The solar sensor is composed of six photodiodes that are divided into two sets; each set is held and oriented on the satellite by its corresponding support printed in Delrin. The paper describes the choice of components, the electrical diagram, and the manufacture of the supports. The methodology followed to obtain the response curve of each photodiode is simple and inexpensive, as it requires a limited number of instruments and tools. The selected irradiance source was a set of red LEDs and halogen instead of an AM0 spectrum irradiance simulator. Some early results from the UPMSat-2 mission have been analyzed in the present paper. Data from magnetometers and the attitude control system have been used to validate the data obtained from the sun sensor. The results indicate a good performance of the sensors during flight, in accordance with the data from the ground tests.
In this paper, the first work carried out at the IDR/UPM Institute within the frame of the educational innovation project PIRAMIDE is presented. This work is related to photovoltaic behavior modeling simplification. The aim is to derive simplified and easy-to-work-with equations for the Lambert W-function. This mathematical function represents a quite useful tool when modeling solar cells/panels performance (that is, the current-voltage curve) by analytical approaches. However, the Lambert W-function has a complex solving process which might represent an unaffordable mathematical challenge for a great number of professionals/technicians from the photovoltaic industrial sector. Simple approximations for the Lambert W-function on both of its branches (positive and negative), are proposed in this work. The results of the present work show a simple but accurate way of photovoltaic systems modeling, even when working with the implicit equation of the 1-Diode/2-Resistor equivalent circuit model (whose solution is given in the present work by an explicit equation).